CSK/Majesty Intercooler Piping

[agentsmith988]

So I found this intercooler piping set on Aliexpress for $50. I figured heck, why not give it a try? It was the cheapest price I could find for an eBayish type kit.

I've got a Treadstone TR6 to pair it up with but before I go tearing into it I had a question about the MAP sensor. I've got a feeling that the bung that is welded into this kit isn't going to mate up too well.. Does anyone have a sensor on hand to measure so I can see how far off it'll be? I can deal with plumbing adjustments during the install.. It's the bung that I want to have sorted out before I dig in.

[iamshayan]

looks like the exact same one that was on my cts turbo piping. should fit fine.

[agentsmith988]

looks like the exact same one that was on my cts turbo piping. should fit fine.

Was the center hole threaded as well on yours?

[mk2rimar]

I got the complet kit with the intercooler its a direct fit but your righ for that hole i had make it biger a tad bit...but thats all you have to do.hope it heps you hoo and by the way you will need 2 screws as the ones that are used on the oem cooler are not at all the same tred

Sent from my Nexus 4 using Tapatalk

[Charles.waite]

Can we talk about, just for a moment, THAT A PIPING KIT EXISTS FOR $50!!!!!!

Also why not just unbolt the MAP super quick and, I don't know, just slap it on there super quick?

[iamshayan]

Can we talk about, just for a moment, THAT A PIPING KIT EXISTS FOR $50!!!!!!

Also why not just unbolt the MAP super quick and, I don't know, just slap it on there super quick?

bc 9/10 one of the screws are rusted to the smic. will break in the smic and leave you with one bolt to reassemble.

[ZipMeUpJ]

Its the same kit someone else posted from ebay a while back. On ebay its about ~150. Its ~100 on aliexpress after shipping

[gmudan]

I wanna but this kit! Link?

[ZipMeUpJ]

this is the one i found on aliexpress here

[agentsmith988]

this is the one i found on aliexpress here

That's a bummer. I bought mine just a few weeks ago from a seller that had free shipping. They've since disappeared... Like most of them usually do on places like AliExpress or DHGate.

The other thing to keep in mind is the piping diameter of 2". With my TR6 I needed to pickup a pair of 2.5" to 2" couplers to make everything work. I got them here on Amazon for cheap.

[mk2rimar]

This is exactly the kit i got and installed.the piping is exactly the same i dint used the elbow silicone hose i cut part of it to make a straight section then you have to remove the secondary air pump pass the piping and try to put it back with modified bracket that's wath i did..... http://m.ebay.ca/itm/191223588262?nav=SEARCH ......and its perfect

Sent from my Nexus 4 using Tapatalk

[llau515]

Sorry for the bump, but does any one know the inner diameter of the hot side/cold side piping, or can someone measure it? Thanks!

[ZipMeUpJ]

the other thread i found says it measured at 1.75" in the pipes and 2" in the couplers. I hope its not 1.75" piping, I was about to buy this kit and that seems too small

[agentsmith988]

the other thread i found says it measured at 1.75" in the pipes and 2" in the couplers. I hope its not 1.75" piping, I was about to buy this kit and that seems too small

The ones I installed were 2" throughout. The only caveat of the setup was needing to remove the threading from the MAP sensor mount hole and getting new screws to fit the threads. Easy stuff

[ZipMeUpJ]

what type of screws did you use?

[agentsmith988]

what type of screws did you use?

I don't remember. I just brought the piping and MAP sensor with me to the hardware store and found the best fit. All I remember is that it was a metric setup. Sorry!

[APC123]

So im guessing 2" hot & cold side of intercooler is the regular size?

[agentsmith988]

So im guessing 2" hot & cold side of intercooler is the regular size?

Look at post #10 for the adapters I used for my Treadstone TR6. 2" to 2.5" couplers.