B8/B8.5 VCDS & Hidden Menu: The Complete List

[vincent9993]

I've been trying to compile a complete list of VCDS mods specific for our S4 cars. I started going through the B8 A4 Cool VAG-COM codes thread but the info is spread over 30 pages and repeats or is trivial. AudiEnthousiasts has also started to put a list together organized by category for the A4. I like his idea but I think there's a need for a straight list of cool VAG-COM mods specific to our S4 and a detail how-to consice in one document.

Please note, I'm not trying to steal or take credit for these mods, I've simply used the information available throughout the web and tried to bring them in a central place. Your help in filling in a few blanks and validating my info would be appreciated.

*Suggestion: Print this and check off the mods you've activated and store it with your owner's manual - Will come handy when you need to re-do the coding after an ECU flash.

Here's the list I've compiled so far:

• Disable After-wipe of windscreen wipers
• Disable amber corner lights
• Disable amber side markers
• Disable Key warning (keyless models)
• Disable LED 'wink' on turn signal
• Disable "Lights are on" warning
• Disable NAV & Phone warning messages while entering data at speed
• Disable Seatbelt Chime
• Enable Adaptive brake lights
• Enable Ambient Interior Lighting Control
• Enable Automatic Gear selection shown in DIS
• Enable Automatic Hill Hold Assist 'lite'
• Enable Auxiliary ventilation
• Enable Battery meter
• Enable DIS with Efficiency Program
• Enable Double Disarm Beep
• Enable DRL Selectable via MMI
• Enable DRL
• Enable Euro parking lights that turn on signal at night
• Enable fog lamp to come on for the same side as that turn signal
• Enable Front Turn Signals as Parking lights
• Enable Gauge Test/Needle Sweep
• Enable Hidden menu in MMI
• Enable Import CDs to MMI's HD
• Enable Independent Fogs control with high beams
• Enable Lap Timer
• Enable LEDs remain bright for parking lights
• Enable Rear Tail Lights on with DRLs
• Enable Release Parking Brake without putting foot on Brake
• Enable Release Parking Brake without putting seatbelt
• Enable Remote Operation windows&sunroof
• Enable Reverse mirror tilt
• Enable Speed through MMI
• Enable TPMS
• Enable VIM on MMI
• Set Audi parking system - Switch OFF Speed
• Set Custom ADS settings
• Set Headlight washer - cycles
• Set Headlight washer - duration
• Adjust Consumption in DIS
• Adjust LED Brightness

Audi A4/S4 B8
VCDS (VAG-COM) codes

Disable After-wipe of windscreen wipers
[09 – Cent. Elect.] [Coding - 07] -> [Dropdown] -> "x ** 8K1 955 119 ** WWS xxxx" -> Long Coding Helper -> Byte 1
Bit 3 - Remove check mark (1 = active)
________________________________________
Disable amber corner lights
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 10
Submodule 0
Bit 3 - Set to 0 to disable amber side markers (U.S. vehicles)
________________________________________
Disable Key warning (keyless models)
[46 – Central Conv.] [Coding - 07] -> Long Coding Helper -> Byte 9
Bit 7 set to 0 (Uncheck)
________________________________________
Disable LED 'wink' on turn signal
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 3
Bit 2 - LEDs remain at full brightness with parking lights (1 = active)
Bit 7 - Turn off LED-strip DRLs with indicators (1 = active)
________________________________________
Disable "Lights are on" Warning
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 5
Bit 3 - Set to 0 to disable "lights are on" warning when you open the door.
________________________________________
Disable NAV & Phone warning messages while entering data at speed
[5F - Information Electr.] -> Adaptation -> Set channel 2 & 3 to 250
________________________________________
Disable Seatbelt Chime
[17 - Instruments] [Coding - 07] -> Long Coding Helper -> Byte 0
Bit 2-4 – Seat Belt Warning inactive
________________________________________
Enable Adaptive brake lights
[46 - Comfort System] [Coding - 07] -> Long Coding Helper -> Byte 8
Bit 0 – Emergency Brake Flashing via Turn Lights active (1 = active)
Bit 1 – Emergency Brake Flashing via Brake Lights active (1 = active)
________________________________________
Enable Ambient Interior Lighting Control
[Hidden menu] [car] [carmenuoperation] [interior light] Set to 5
[Hidden menu] [car] [cardevicelist] [interior light] Enable
Reset MMI
________________________________________
Enable Automatic Gear selection shown in DIS
[02 – Auto Trans] [Adaptation – 10]
Select “Single Gear Display” from top channel drop down menu
Select “D on/S on” from New value drop down menu
________________________________________
Enable Automatic Hill Hold Assist ‘lite’
[03 - ABS brakes][Security Access - 16] (Enter code presented by program)
[Coding – 07] -> Long Coding Helper -> Byte 1
Bit 6 set to 1 to enable hill hold assist.

http://www.audizine.com/forum/showth...r-the-A4/page2
________________________________________
Enable Auxiliary ventilation
[5F - Information Electr.] [Coding - 07] -> Long Coding Helper -> Byte 6
Bit 1 – Set to 1
[Hidden menu] [car] [cardevicelist] [Auxiliary heating] Enable
[08 - Auto HVAC] [Coding - 07] -> Long Coding Helper -> Byte 1
Bit 3 – Set to 1
Bit 4 – Set to 1
________________________________________
Enable Battery meter
[Hidden menu] [car] [cardevextdevicelist] [Battery] Enable
[Hidden menu] [car] [carmenuoperation] [Battery] Set to 5
Reset MMI
or
[56 - Radio] -> Adaption -> Channel 39, add 16 to your value
________________________________________
Enable DIS with Efficiency Program for MY2010+ (Not a complete Program without the Start/Stop System)
[17 - Instruments] [Adaptation - 10] -> Channel 77
change 0 to 255
________________________________________
Enable Double Disarm Beep
[46 - Central Conv.] [Adaptation - 10] -> Channel 63
Add 4
________________________________________
Enable DRL Selectable via MMI
[09 – Cent. Elect.] -> [Coding – 07] -> Long Coding Helper -> Byte 3
Bit 5 set to 1
________________________________________
Enable DRL
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 2
Bit 1 = DRL via Front Side markers
Bit 2 = DRL via High Beams
Bit 3 = DRL via Fogs
Bit 4 = DRL via LEDs
Bit 6 = DRL via Side markers
Bit 7 = DRL via Tail lights
________________________________________
Enable Euro parking lights that turn on signal at night
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 9
Bit 0 - Set to 1
________________________________________
Enable fog lamp to come on for the same side as that turn signal
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 4
Bit 0 - Check the box or change :Bit 0 set to 1
________________________________________
Enable Front Turn Signals as Parking lights
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 10
Bit 0- Check the box or change :Bit 0 to 1
Once the change has been made you can enable the front turn signals as DRL's by making the following change:
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 2
Bit 6 - Check the box or change :Bit 0 set to 1
________________________________________
Enable Gauge Test/Needle Sweep
[17 - Instruments] [Coding - 07] -> Long Coding Helper -> Byte 1
Bit 0 - Check the box for "Gauge Test/Needle Sweep active"
________________________________________
Enable Headlights on all the time
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 4
Bit 5 - Check the box or change :(Bit 5 Set to 1)
________________________________________
Enable Hidden menu in MMI
[5F - Information Electr.]
[Adaptation - 10] -> Channel 6
change 0 to 1
Use this hidden menu at your own risk.
Caution: Keep away from the "Bootloader"
________________________________________
Enable Import CDs to MMI's HD
[Hidden menu]
Main/Diagnose/Settings
Import Media
Set to 4 of 4 "Copy/Ripping"
________________________________________
Enable Independent Fogs control with high beams
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 4
Bit 1 – (Front) Uncheck the box or change :Bit 1 to 0
Bit 2 – (Rear) Uncheck the box or change :Bit 2 to 0
________________________________________
Enable Lap Timer
[17 - Instruments] [Coding - 07] -> Long Coding Helper -> Byte 1
Bit 3 - Check the box for "Lap Timer active"
______________________________________
Enable Remote Operation Windows and Sunroof
[46 - Cent. Conv.] [Coding - 07] -> [Long Coding Helper] Byte 2
Bit 2 - Set to 1
______________________________________
Enable Rear Tail Lights on with DRLs
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 2
Bit 7 - DRL's via Tail Lets Active (1 = Active)
________________________________________
Enable Release Parking Brake without putting foot on Brake
[53 - Parking Brake][Security Access - 16] (Enter code presented by program)
[Adaptation - 10] -> Channel 4 Set to 0
________________________________________
Enable Release Parking Brake without putting seatbelt
[53 - Parking Brake][Security Access - 16] (Enter code presented by program)
[Adaptation - 10] -> Channel 7 Set to 0
________________________________________
Enable Reverse mirror tilt
[52 Door Elect, Pass.] -> [Coding - 07] -> [Long Coding Helper] -> Byte 4
Bit 4 and Bit 2 set to 1
________________________________________
Enable Speed through MMI
[56 - Radio] [Adaptation - 10] -> Channel 02, Set to 1
Does not work if NAV equiped
________________________________________
Enable TPMS
* You need the 1AT ABS unit – check your stickers (1AS does not work)
[Hidden menu] [car] [cardevicelist] [RDK] Enable
[Hidden menu] [car] [carmenuoperation] [Tires Air Pressure Control] Set to 5

[03 - ABS Brakes]
[Security Access - 16] (probably with login code: 61378)
[Coding - 07] -> Long Coding Helper -> Byte 1
Bit 3 - Tire Pressure Monitoring (PR-7K6) active (1 = active)

The TPMS need to be enabled in the Instrument Cluster:
[17 - Instruments]
[Coding - 07] -> Long Coding Helper -> Byte 4
Bit 0 - Tire Pressure Monitoring (TPMS) installed (1 = active)
Reset MMI
________________________________________
Enable VIM on MMI
[5F - Information Electr.] [Advanced ID - 1A] Note 1st Serial number
[Security Access] Enter Digits 6, 13, 10, 14, 11 of the 1st Serial number
[Adaptation - 10] -> Channel 48
Set to 255
Reset MMI
________________________________________
Set Audi parking system - Switch OFF Speed
[10 - Park/Steer Assist] [Adaptation - 10] -> Channel 23
Set to 20 (max value in km/h)
________________________________________
Set ADS to specific preset Comfort, Auto, Dynamic or Individual
[09 – Cent. Elect.][Security Access - 16]
[Adaptation - 10] -> Channel 63
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
[Adaptation - 10] -> Channel 64
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
[Adaptation - 10] -> Channel 65
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
[Adaptation - 10] -> Channel 66
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
*Note all four channels needs to be set to the same value.

________________________________________
Set Headlight washer - Duration
[09 – Cent. Elect.]
[Security Access - 16] [Adaptation - 10] -> Channel 6
change to e.g. 500
________________________________________
Set Headlight washer - Cycles
[09 – Cent. Elect.]
[Security Access - 16] [Adaptation - 10] -> Channel 26
change to e.g. 10
________________________________________
Adjust Consumption in DIS
[17 - Instruments]
[Adaptation - 10] -> Channel 3
change 100 to xxx (see samples below)

Sample 1 - Calculation based on volume per distance (e.g. l/100km):
DIS: 9,3 l/100 km.
Real: 9,8 l/100 km. (100 * 9,8 / 9,3 = 105,38)
Channel 3 will be changed from 100 to 105

Sample 2 - Calculation based on distance per volume (e.g. MPG):
DIS: 23 MPG.
Real: 24 MPG. (100 * 23 / 24 = 95,83)
Channel 3 will be changed from 100 to 96
________________________________________
Adjust LED brightness
[09 – Cent. Elect.] [Security Access - 16] (enter security code. One of the default codes is- 20113)
[Adaptation - 10] -> Channel 3
Set between 5 and 100
________________________________________
Set Automatic Transmission Start Mode to D or S
[09 - Cent. Elect.] [Security Access - 10]
[Adaptation 10] -> Channel 64 - Stored Value = 218 = Starting mode is always D

Channel 64 - New Value = 00; Starting mode is determined by ADS selection at engine shutdown (Comfort and Auto=D, Dynamic=S, Individual=whatever you pick)
Channel 64 - New Value = 03; Starting mode is always S regardless of ADS selection at engine shutdown (opposite of stock)
Channel 64 - New Value = 11; Starting mode is S with all ADS settings at shutdown except Comfort where it's D
Channel 64 - New Value = 19; Starting mode is S with all ADS settings at shutdown except Auto where it's D
________________________________________

Again, I take no credit for this information, most of the above is available on these forums and specialty websites as well as Ross-Tech's support pages. I only wanted to group all the info of the pertinant VCDS mods to our S4.

Not all the above has been verified, I'll be happy to re-edit this post to correct any info.
Oh and I'm not responsible for any screw ups this causes, good luck.

Can I get a few volunteers to nominate this post as a sticky?

[NWS4Guy]

I have on my car:

Disable amber corner lights


And I also know of some others off the top of my head:

Change "Auto" settings to mirrow "Individual" so that you start the car in whatever mode you want
Enable fog lamp to come on for the same side as that turn signal (sort of like an extra light on that corner when turning)

[Kczach]

There is also a way via mmi that you can burn cd's to your hard drive directly. There is a thread somewhere on how to do it.

[vwong]

I believe there is also the A/C ventilation so that you can set the fan to come on before you enter the car. It's great for hot summer days. I have this in my BMW, and I love it.

[asm777]

[*]Enabling Gauge Test/Needle Sweep [*]Enable TPMS [*]Seat Memory [*]DIS with Efficiency Program [*]Disable Key Warning

Few questions and comments:

Aren't these already enabled from the factory on the S4?[*]Enabling Gauge Test/Needle Sweep[*]Enable TPMS [*]DIS with Efficiency Program

I understood that this mod only works on the A5/S5 (w/o seat mem) because the control module is already there that allows the seat to move forward to let passengers into the back seats. No go for our S4s unless you have Prestige trim:[*]Seat Memory

I don't suppose this is the "LIGHTS ON" warning that buzzes incessantly when you have the key in and the door open? If so, can you share the coding?[*]Disable Key Warning

Thanks!

[vincent9993]

Few questions and comments:

Aren't these already enabled from the factory on the S4?[*]Enabling Gauge Test/Needle Sweep[*]Enable TPMS [*]DIS with Efficiency Program

I understood that this mod only works on the A5/S5 (w/o seat mem) because the control module is already there that allows the seat to move forward to let passengers into the back seats. No go for our S4s unless you have Prestige trim:[*]Seat Memory

I don't suppose this is the "LIGHTS ON" warning that buzzes incessantly when you have the key in and the door open? If so, can you share the coding?[*]Disable Key Warning

Thanks!

• Enabling Gauge Test/Needle Sweep - Yes mine was, I assume not all had it
• Enable TPMS - Not mine as I did not order TPMS
• DIS with Efficiency Program - Yes mine was, I assume not all had it

Not sure about the rest...

[NWS4Guy]

TPMS is only standard on US cars, as it's required. Canada used to be SOL because it was a sensor in the vavle stem, now it uses the ABS system to monitor wheel rotations and changes in them at speed to determine differences in circumference due to pressure drops - and VCDS can enable it.

Efficiency is standard on 2011, it's there and hidden on 2010, but several had gotten MMI updates at their service interval which added this.


The LIGHTS ON has not been found yet, but you CAN tap the reset button that you use to toggle the DIS between screens and it will immediately silence this alarm.

[asm777]

The LIGHTS ON has not been found yet, but you CAN tap the reset button that you use to toggle the DIS between screens and it will immediately silence this alarm.

Oh, thanks! At least a temporary solution until someone figures it out!

[Deep Sea S4]

I am not sure what enable speed via MMI is?

Does that show your speed on the LCD screen?

[iceboss23]

The LIGHTS ON has not been found yet, but you CAN tap the reset button that you use to toggle the DIS between screens and it will immediately silence this alarm.

Can you pls explain what reset button you are talking about here?

[A5MD]

^^^ More info in ref. to this: http://www.audizine.com/forum/showth...when-lights-on

[dr bryan]

Anyone know if you can change (increase) the sensitivity of the automatic wipers via mmi? That would be GREAT!

[2010S4]

Anyone know if you can change (increase) the sensitivity of the automatic wipers via mmi? That would be GREAT!

Can't they be adjusted via the little button on top of the wiper stalk. I always thought that is what that thing did.

[NWS4Guy]

Well it's a switch with several stopping points, but yes :)

[Dave-B8S4]

i definately need to get rid of the "Lights are on" warning sound. when you open the door with your headlights on. its BLOODY ANNOYING!!

[vincent9993]

Updated my post, what do you think?

[Leor604]

Great work, Vincent. Thread subscribed. Now all I need is the S4 (April delivery )

[scottyuk]

Great thread - good work.



Regarding "Set ADS to Individual"

You could include in the list setting them all to 01, 02 or 03 i.e. Comfort, Auto, Dynamic

There's also Rear Lights on with DRLs :

[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 2
Bit 7 - DRL's via Tail Lets Active (1 = Active)

Enable Import CDs to MMI's HDGo into Hidden Menu
Main/Diagnose/Settings
Import Media
Set to 4 of 4 "Copy/Ripping"

[NWS4Guy]

Here's a combination of some I mentioned you couldn't find, one makes the DRL's 100% bright always, the other disables the amber sidemarker lights, allowing full bright DRL's with no front lights on while Parking lights are on:

Enable DRL full bright
- Module 9 - Central Electric
- Secure Access (use access code 20113 to unlock this module for modification)
- Choose Adaptation
- Channel 3, change this value to 100 (which is percentage of the brightness for the DRL's, anything under 5 turns the LED's off and will generate an error code on the DIS)

Disable amber sidemarker with parking lights
[09 – Cent. Elect.]
[Coding - 07] -> [Long Coding Helper] -> Byte 10 Bit 3 - Change 1 to 0

[vincent9993]

Here's a combination of some I mentioned you couldn't find, one makes the DRL's 100% bright always, the other disables the amber sidemarker lights, allowing full bright DRL's with no front lights on while Parking lights are on:

Enable DRL full bright
- Module 9 - Central Electric
- Secure Access (use access code 20113 to unlock this module for modification)
- Choose Adaptation
- Channel 3, change this value to 100 (which is percentage of the brightness for the DRL's, anything under 5 turns the LED's off and will generate an error code on the DIS)

Disable amber sidemarker with parking lights
[09 – Cent. Elect.]
[Coding - 07] -> [Long Coding Helper] -> Byte 10 Bit 3 - Change 1 to 0

These are listed as:
* Adjust LED brightness
* Disable amber corner lights

I've named them slightly differently but they achieve the same result.

[vincent9993]

Great thread - good work.



Regarding "Set ADS to Individual"

You could include in the list setting them all to 01, 02 or 03 i.e. Comfort, Auto, Dynamic

There's also Rear Lights on with DRLs :

[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 2
Bit 7 - DRL's via Tail Lets Active (1 = Active)

Enable Import CDs to MMI's HDGo into Hidden Menu
Main/Diagnose/Settings
Import Media
Set to 4 of 4 "Copy/Ripping"

Thanks for the info, I've added it to the post.

[NWS4Guy]

Then you can remove the "LED's remain bright with Parking Lights" as could not find.

What is this one?

Enable DRL via LEDs active
Could not find this one

[vincent9993]

Then you can remove the "LED's remain bright with Parking Lights" as could not find.

What is this one?

Enable DRL via LEDs active
Could not find this one

Thanks, I'll remove the "LED's remain bright with Parking Lights" then. The "Enable DRL via LEDs" is to customize which lights (ie: LEDs, fog, etc) are used as DRL IIRC. The title is a little off and this is probably why I could not find my notes on this. I'll vag my car this week end and I update it.

[HAWKiS5]

Great list, thx! I already did most of it last week on my car, and I am still checking if all works.

This one you can add which is very convenient for peope who have Adaptive Cruise:

From the Auto distance regulation module 13, Adaptation, Channel 7, change 0 to 1

This gives you extra entry in MMI/ACC where you can change the default distance.

BTW: a question about some default settings when starting the car:
- anybody knows how to get the AHA (hill hold) automatically ON (now you have to put it on every times again)?
- same for high-beam assist?
- same for showing preset Memory Radio (and TV) stations first (now it always starts with a list of available channels, but I want to use the memory presets always)
TIA!

[S4Tokyo]

Great list, thx! I already did most of it last week on my car, and I am still checking if all works.

This one you can add which is very convenient for peope who have Adaptive Cruise:

From the Auto distance regulation module 13, Adaptation, Channel 7, change 0 to 1

This gives you extra entry in MMI/ACC where you can change the default distance.

BTW: a question about some default settings when starting the car:
- anybody knows how to get the AHA (hill hold) automatically ON (now you have to put it on every times again)?
- same for high-beam assist?
- same for showing preset Memory Radio (and TV) stations first (now it always starts with a list of available channels, but I want to use the memory presets always)
TIA!

'high beam assist...' = auto hi-lo beam?? If so, that requires separate HW/SW, which by sound of things you don't already have. It uses CMOS Sensor & special algorithms - 'separate' option of Interior Mirror sub-assy - for detecting fwd (opposite lane) and rear (same lane) vehicle source lighting, also sensing for street lights, neon signs, you name it so as not to false adjust and adjusting beam height accordingly. It cannot be VAG'd, at least not in the true definition of intelligent headlamp control.

[HAWKiS5]

'high beam assist...' = auto hi-lo beam?? If so, that requires separate HW/SW, which by sound of things you don't already have. It uses CMOS Sensor & special algorithms - 'separate' option of Interior Mirror sub-assy - for detecting fwd (opposite lane) and rear (same lane) vehicle source lighting, also sensing for street lights, neon signs, you name it so as not to false adjust and adjusting beam height accordingly. It cannot be VAG'd, at least not in the true definition of intelligent headlamp control.

Sorry if my question was not clear: if already have high-beam assist (= auto-high beam) so all the hw is there and it work. The only question is: is it possible to have it on ALWAYS (now it is OFF by default, just like the AHA function and the list of radio stations is NOT on Memory view by default.....)

TIA

[S4Tokyo]

Sorry if my question was not clear: if already have high-beam assist (= auto-high beam) so all the hw is there and it work. The only question is: is it possible to have it on ALWAYS (now it is OFF by default, just like the AHA function and the list of radio stations is NOT on Memory view by default.....)

TIA

My misunderstanding, however I don't have answer that you can act on:-(
Technically it's possible, I guess the 12V line to this high beam assist would need to be altered electronically from ON/OFF switch to constant on i.e. VAG control;-) or physically by modifying power line to 12V IGN line. You need smarter person than myself to advise - good hunting though:-)

[FINA4]

Enable DRL Selectable via MMI
[09  Cent. Elect.] -> [Coding  07] -> Long Coding Helper -> Byte 3
Bit 5 set to 1

What is it supposed to do? I tried this but didn't see anything different in MMI.

[S5noob]

It would be great if we could set the wiper sensitivity more than the max that the wiper stalk adjuster can offer. I'm always at max setting as it is, and it would be nice to move the whole range up, so that my daily setting is in the middle. Can the sensitivity be adjusted by vagcom?

Can't they be adjusted via the little button on top of the wiper stalk. I always thought that is what that thing did.

[rlarsen]

Enable DRL Selectable via MMI
[09 Cent. Elect.] -> [Coding 07] -> Long Coding Helper -> Byte 3
Bit 5 set to 1

What is it supposed to do? I tried this but didn't see anything different in MMI.

Bit 5 should enable/disable the MMI menu item for "Daytime running lights" under "Car->Exterior lighting"

[B8SlineNate]

nice

[NWS4Guy]

Enable DSG gear displayed when in D or S in the DIS (thanks to kmjmrq - http://www.audizine.com/forum/showth...=1#post6093594)

[02 - Auto Transmission]
[10 - Adaptation]
Use the drop down menu and scroll way down near the bottom and select Single Gear Display
In the lower drop down labeled "new," select D on/S on
Do it! - you will get a popup saying this is not a standard change and the would you like to use the generic Shop Code and the string is shown - accept this and it will rescan the module.

The DIS will now show Dx and Sx where "x" is the current gear you are in just like it should!

[Voltrons_Head]

^^I saw this today. How great is this? Have you done it yet?

[NWS4Guy]

^^I saw this today. How great is this? Have you done it yet?

I love it, worked great, I literally went right out to my car and tried it immediately. I put in the extra parts about the Shop Code, as that was what I was prompted. Stupid that they made the default to hide it in the car, and it's still there. I even remember someone saying the talked to a guy from Audi AG, who said they knew the new DSG code removed this when they flashed the A3's back before the S4 came out in B8 flavor - he said they would not be making it change back, there was no way to easily in the code - hah!

This removes one of the small gripes I had about the DSG.

[zee007]

Enable DSG gear displayed when in D or S in the DIS (thanks to kmjmrq - http://www.audizine.com/forum/showth...=1#post6093594)

[02 - Auto Transmission]
[10 - Adaptation]
Use the drop down menu and scroll way down near the bottom and select Single Gear Display
In the lower drop down labeled "new," select D on/S on
Do it! - you will get a popup saying this is not a standard change and the would you like to use the generic Shop Code and the string is shown - accept this and it will rescan the module.

The DIS will now show Dx and Sx where "x" is the current gear you are in just like it should!

Fantastic find. I wonder if this works for the S-tronic B8 (like the S5)?

[rlarsen]

Fantastic find. I wonder if this works for the S-tronic B8 (like the S5)?

Tiptronic, S-Tronic (or DSG which is the name VW use) and Multitronic can all be coded - so it should work on your S5.

[HAWKiS5]

It works on my S5. It shows Dx and Sx. It is not showing the "gear advice" however, that was shown in my S5 coupe before (then it showed for instance D4->5, meaning it is advisable to change gear from 4 to 5).

[NWS4Guy]

Fantastic find. I wonder if this works for the S-tronic B8 (like the S5)?

I have the B8 with S-tronic...

[MeteorS4Ti]

Set ADS to Individual
[09 – Cent. Elect.][Security Access - 16]
[Adaptation - 10] -> Channel 63
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
[Adaptation - 10] -> Channel 64
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
[Adaptation - 10] -> Channel 65
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
[Adaptation - 10] -> Channel 66
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
*Note all four channels needs to be set to the same value.

So if I put each of the settings into 04- Individual I can go back to my car and change the settings from then on? Looking to do this within the next couple days so I'd appreciate any help.

[Matt427]

So if I put each of the settings into 04- Individual I can go back to my car and change the settings from then on? Looking to do this within the next couple days so I'd appreciate any help.

Yes, the hardware buttons will still work to change to whatever ADS setting you like.

Incidentally, I think "Set ADS to Individual" is mislabeled since this code can be used to set the default ADS to any of those four settings, not just Individual. For example, I used code 03 - Dynamic to set Dynamic as the default setting.