TT RS wheel fitment and info

[ormandj]

We should have a thread for wheels known to fit and specifications of said wheels.

I'll start with some stock information, since I was unable to find it elsewhere. I pulled the wheel off and weighed it an hour ago or so.

Audi (stock BO) 20x9:

Fits: Yes, no modifications needed
ET: 52
Weight: 50.4lbs with stock PZero 255/30R20, which is specified as 23lbs, so 27.4lbs for the wheel (!!!!!)

[Lusky]

Mine weighed more than that so either the wheel or the tire is slightly heavier


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[mossback]

27 lbs for the TTRS OEM Forged 20" wheel? That doesn't seem right. The TTS forged 20" wheel is significantly lighter. Even my low pressure cast OEM 19" wheel is a hair lighter than that (although a BBS SX cast 18" wheel is 29 lbs, so one never knows).

Methinks Pirelli may be off on their tire weight spec's!

I don't want to mess up your thread lineage intentions so no response needed and will delete this post in a bit.
.
They maybe forged but they are heavy pigs. I dropped about 6lbs a corner going with my wheel tire combo

[ormandj]

Mine weighed more than that so either the wheel or the tire is slightly heavier


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

What did yours weigh? You had the P Zeros/20" BO? My tires have around 2100 miles on them.

[Cale262]

I see Tirerack now has wheels listed for the MK3 TT RS.

[chasiu]

is the fitment for wheels on the TTRS different from the TT or TTS other than brake clearance

[Rapture]

I see the the Tire Rack lists the BBS FI R as a fitment with a 38 offset. I wonder if they have tried them on? Must be the Lamborghini wheel. Cool but $$$$$


Rapture

[Lusky]

is the fitment for wheels on the TTRS different from the TT or TTS other than brake clearance

Just brake clearance


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[sciblades]

Does anyone know the ET with carbon ceramics?

Sent from my SM-G955U using Tapatalk

[wildtouch83]

Does anyone know the ET with carbon ceramics?

Sent from my SM-G955U using Tapatalk

If I'm not mistaken, when you get the dynamic package w/ the ceramics you automatically get the 20x9 ET52 wheels.

[chasiu]

I see the the Tire Rack lists the BBS FI R as a fitment with a 38 offset. I wonder if they have tried them on? Must be the Lamborghini wheel. Cool but $$$$$


Rapture

What is the width of the wheel though?

[wildtouch83]

What is the width of the wheel though?

20x9

[sciblades]

If I'm not mistaken, when you get the dynamic package w/ the ceramics you automatically get the 20x9 ET52 wheels.Yes but I want to put a 19 on there so need to find out what will fit

Sent from my SM-G955U using Tapatalk

[Cream]

My new TTRS arrives in about a week. Right now for my current TTRS I have about 4 different VMR wheel sets. I will be trying those out, hoping they will fit

[Mops@Nemesis]

My FS arrived yesterday. They'll be a good option for those that want the best/lightest for less than the basic US forged options.

http://bbs-japan.co.jp/en/products/1422/

My 9.5 ones weight 20.2 pounds.

https://farm5.staticflickr.com/4461/37401447050_bb5e53d84e_o.jpg (https://flic.kr/p/YZ3cam)Untitled (https://flic.kr/p/YZ3cam) by Audiyos (https://www.flickr.com/photos/91999203@N06/), on Flickr

https://farm5.staticflickr.com/4483/37401447020_fbf7ddaae5_o.jpg (https://flic.kr/p/YZ3c9Q)Untitled (https://flic.kr/p/YZ3c9Q) by Audiyos (https://www.flickr.com/photos/91999203@N06/), on Flickr

[wildtouch83]

Oh my mops! What are the size options with these?

Sent from my SM-G950U1 using Tapatalk

[Mops@Nemesis]

Oh my mops! What are the size options with these?

Sent from my SM-G950U1 using Tapatalk

Click that link to the Japan site [up]

You'll not find them on the US site yet. Mine are the first ones in the US. They arrived to BBS yesterday.

[Chuckster]

Awesome wheel. Might be my Q1 gift to myself.

[Mops@Nemesis]

Awesome wheel. Might be my Q1 gift to myself.

Happy to make that happen 😎 Doesn't get much better. Die-forged goodness.

[ormandj]

Happy to make that happen 😎 Doesn't get much better. Die-forged goodness.

Which model(s) is(are) a confirmed fit with the TT RS without issue, and with what tire size? Brake clearance has been a real issue with these cars.

Also, price in the states?

[Mops@Nemesis]

Which model(s) is(are) a confirmed fit with the TT RS without issue, and with what tire size? Brake clearance has been a real issue with these cars.

Also, price in the states?

The 19x9.5 ET45 pictured below. I actually just got mine and snapped these. Not sure on tire size, but I can check. These list at $5K. The 19x8.5 ET42 would work too, but spacers may be wanted for the correct look. I think I would run 8mm spacers personally.

https://farm5.staticflickr.com/4462/37696249236_ca8ddd9513_o.jpg (https://flic.kr/p/Zr68zE)IMG_7040 (https://flic.kr/p/Zr68zE) by Audiyos (https://www.flickr.com/photos/91999203@N06/), on Flickr

https://farm5.staticflickr.com/4494/37486615200_868df35454_o.jpg (https://flic.kr/p/Z7yGFJ)IMG_7033 (https://flic.kr/p/Z7yGFJ) by Audiyos (https://www.flickr.com/photos/91999203@N06/), on Flickr

https://farm5.staticflickr.com/4496/37696255366_816e046687_o.jpg (https://flic.kr/p/Zr6apm)IMG_7037 (https://flic.kr/p/Zr6apm) by Audiyos (https://www.flickr.com/photos/91999203@N06/), on Flickr

https://farm5.staticflickr.com/4498/37486613330_0883dd4be9_o.jpg (https://flic.kr/p/Z7yG8u)IMG_7035 (https://flic.kr/p/Z7yG8u) by Audiyos (https://www.flickr.com/photos/91999203@N06/), on Flickr

https://farm5.staticflickr.com/4509/37486616460_06dcde2fbc_o.jpg (https://flic.kr/p/Z7yH4s)IMG_7028 (https://flic.kr/p/Z7yH4s) by Audiyos (https://www.flickr.com/photos/91999203@N06/), on Flickr

https://farm5.staticflickr.com/4508/37696252736_5993d4a78a_o.jpg (https://flic.kr/p/Zr69C1)IMG_7039 (https://flic.kr/p/Zr69C1) by Audiyos (https://www.flickr.com/photos/91999203@N06/), on Flickr

[Rapture]

Mops, do you carry the FIR’s in the fitment for the TT RS (actually the fronts of the R8) and would you have similar photos to those you show above of them? I’ve been focused on the HRE P101 but also like the look of the FIR’s.


Rapture

[sciblades]

Would those fit over ceramics

Sent from my SM-G955U using Tapatalk

[Mops@Nemesis]

Mops, do you carry the FIR’s in the fitment for the TT RS (actually the fronts of the R8) and would you have similar photos to those you show above of them? I’ve been focused on the HRE P101 but also like the look of the FIR’s.

Rapture

You don't want to pay way more for a lesser wheel? ☺️

Email sent to BBS.


Would those fit over ceramics

Sent from my SM-G955U using Tapatalk

Email sent to BBS.

[S 3]

I have BBS CI-R, 19x9 ET42. They weigh in at 25.3lbs each. Also running 10mm spacers.


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[Mops@Nemesis]

Mops, do you carry the FIR’s in the fitment for the TT RS (actually the fronts of the R8) and would you have similar photos to those you show above of them? I’ve been focused on the HRE P101 but also like the look of the FIR’s.

Rapture

BBS....

We do have the 20x9 et35 FI-R in stock but I don’t believe the load capacity is sufficient.
The max front axle load or a R8 or Huracan is about 915 kg. The load for the TT-RS is about 1,050 kg. I don’t know if the FI-R was built to a higher capacity since it was only intended for Audi’s mid-engine cars.
I’ve requested info from Germany. We’ll see what comes back.


Would those fit over ceramics

Sent from my SM-G955U using Tapatalk

Still waiting to hear.

[Lusky]

I’m on 18x9.5 and 275/35’s now
https://uploads.tapatalk-cdn.com/20171017/da923e04904a6894629b804d93dbfafe.jpg


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[Mops@Nemesis]

Would those fit over ceramics

Sent from my SM-G955U using Tapatalk

BBS...

Not sure, I don’t have a ceramic profile.
Audi’s website does not have any description of the size of the ceramics… The standard rotors are 370mm… Theoretically, assuming a caliper of similar dimensions, the wheel can handle a 390mm rotor…

[ormandj]

I’m on 18x9.5 and 275/35’s now
https://uploads.tapatalk-cdn.com/20171017/da923e04904a6894629b804d93dbfafe.jpg


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

Nice! What wheel/tire combo/specs? Let's keep the info coming for people looking for wheel options. How's the handling? I'm about to order some 19x9 ET45 wheels that are ~20lbs each, and go with 255/35R19 tires (lots more options and a half inch more sidewall for street). 9.5" with 265 would be appealing but I'd worry about fitment.

[Lusky]

Nice! What wheel/tire combo/specs? Let's keep the info coming for people looking for wheel options. How's the handling? I'm about to order some 19x9 ET45 wheels that are ~20lbs each, and go with 255/35R19 tires (lots more options and a half inch more sidewall for street). 9.5" with 265 would be appealing but I'd worry about fitment.

TSW Interlagos 18x9.5 et53 275/35-18 RE-71R’s


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[Mops@Nemesis]

Poop cell pic, but it's the best thing I have to share. Amazing what shaving 8 pounds per corner does.

https://farm5.staticflickr.com/4462/37095468293_a193f09faf_o.jpg (https://flic.kr/p/YvZYkx)IMG_9910 (https://flic.kr/p/YvZYkx) by Audiyos (https://www.flickr.com/photos/91999203@N06/), on Flickr

[Mops@Nemesis]

@Rapture

BBS... Confirmed… the FI-R does not have a sufficient load for the TT-RS.

[Rapture]

@Rapture

BBS... Confirmed… the FI-R does not have a sufficient load for the TT-RS.

Thanks very much, I would hate to make that mistake.

[VMRWheels]

VMR V708 19x8.5 ET38 - Confirmed fit
Audizine member audibmi sent us over some photos of this. V708 19x8.5 ET38 pulled from his previous car and installed on his new TT-RS.
Most of our 19x8.5 ET35 wheels should fit TT-RS just fine [up]

https://i.imgur.com/JwZrAxX.jpg

https://i.imgur.com/DkPQDqr.jpg

[Sniper260687]

Personally, I think the Niche wheels look good.

https://farm5.staticflickr.com/4446/37067190754_394fe7299e_o.jpg

https://farm5.staticflickr.com/4453/37744565222_6b2cf92002_o.jpg

[ormandj]

Personally, I think the Niche wheels look good.

https://farm5.staticflickr.com/4446/37067190754_394fe7299e_o.jpg

https://farm5.staticflickr.com/4453/37744565222_6b2cf92002_o.jpg

What's the specifications on the wheels/tires? Any fitment issues? Looks good.

[Sniper260687]

What's the specifications on the wheels/tires? Any fitment issues? Looks good.

Niche misano m116 19x8.5

Nitto Invo 255/35/19

They also offered this model in 20'' but since im lowered, clearance could of been an issue

[Rapture]

Niche misano m116 19x8.5

Nitto Invo 255/35/19

They also offered this model in 20'' but since im lowered, clearance could of been an issue

Your wheels do look nice.

[Sniper260687]

Your wheels do look nice.

Thank you, waiting on spacers!

Ill post pic when done

[Sal85012]

Thinking of going with 18s or 19” torn on whether 18” are too small for the look, i dont plan on tracking. The 20” are too damn big for this car on shitty roads

[mossback]

https://uploads.tapatalk-cdn.com/20171025/12d67c7d1429b62ea06587dbdad17cd5.jpg

i think the 18” looks the business, mind you these are 35’s not 40’s so are slightly shorter than stock diameters. 265/35-18 vs 255/40-18


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[TroySico]

I’m on 18x9.5 and 275/35’s now
https://uploads.tapatalk-cdn.com/20171017/da923e04904a6894629b804d93dbfafe.jpg


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

Lusky,
Can you post super close up pics of your front wheel weight situation????


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[Lusky]

Lusky,
Can you post super close up pics of your front wheel weight situation????


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

I will try and get a pic tomorrow; basically they put them on the back/inside


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[TheBigFish]

I’m on 18x9.5 and 275/35’s now
https://uploads.tapatalk-cdn.com/20171017/da923e04904a6894629b804d93dbfafe.jpg


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

Is your car an RS or S?

[Lusky]

Is your car an RS or S?

RS


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[TheBigFish]

RS


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

Did you have the matte black or the silver wheel powder coated? Also the 275's fit the 9.5 rims almost perfectly, my first requirement is a winter wheel. I'm looking at 255/40/18's DWS Conti's, obviously 9.5 would stretch 255's quite a bit. I'm guessing that 9 inch versions would be about right for my immediate application.

[Lusky]

Did you have the matte black or the silver wheel powder coated? Also the 275's fit the 9.5 rims almost perfectly, my first requirement is a winter wheel. I'm looking at 255/40/18's DWS Conti's, obviously 9.5 would stretch 255's quite a bit. I'm guessing that 9 inch versions would be about right for my immediate application.

Yes had them powder coated gloss black to match the black optics

https://uploads.tapatalk-cdn.com/20171026/354e5d6722ee92dbaf941e7b7cabe9fd.jpg


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[Cream]

So I tried the VMR wheels that I have, I V710 and V703s, both 19x9.5 with a 45 offset. They barely touched the calipers. I put 5mm spacers on and they now clear with the smallest of margin. Will work for my winter wheels.

Sent from my SAMSUNG-SM-G920A using Tapatalk

[TheBigFish]

Yes had them powder coated gloss black to match the black optics

https://uploads.tapatalk-cdn.com/20171026/354e5d6722ee92dbaf941e7b7cabe9fd.jpg


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

Hate to bug you so much on this but I have one more question. In your build thread you show the clearance roughly equal to a piece of cardboard box. In your opinion, is this enough clearance to handle the type of suspension loads one might see at an autoX?

[tommyccbc]

It’s been awhile since I’ve been on the good ole zine, thought this might help.

http://www.willtheyfit.com/wheels/

My new wheels are a comin’ Bk, you’ll be disappointed, they are 20’s. Lol


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[Lusky]

Hate to bug you so much on this but I have one more question. In your build thread you show the clearance roughly equal to a piece of cardboard box. In your opinion, is this enough clearance to handle the type of suspension loads one might see at an autoX?

I drive the car aggressively often they will never hit. I had 265’s now I have 275’s and still clear.


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[wildtouch83]

I drive the car aggressively often they will never hit. I had 265’s now I have 275’s and still clear.


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)I think he was actually inferring that your wheel would flex and somehow contact the brake caliper under strenuous driving... based on the cardboard reference.

:shrug:

Sent from my SM-G950U1 using Tapatalk

[Cream]

I just put my winters on, these have a 45mm offset so I had to use 5mm spacers in front. But good enough for winter. Gives me time to find the right Gloss Black wheels for summer. https://uploads.tapatalk-cdn.com/20171027/c7a9346b2a202a638a5c076646133143.jpghttps://uploads.tapatalk-cdn.com/20171027/dfd75d0075d92c9cb5e930f73b70df80.jpg

Sent from my SAMSUNG-SM-G920A using Tapatalk

[sciblades]

My wheel and tire setup comes on Wednesday

Sent from my SM-G955U using Tapatalk

[TheBigFish]

Ok so I ordered the 18x9.5 et53 TSW Interlagos and some Conti DWS 255/40/18's for the cold weather. I hesitate to say winter since I live in North Alabama. If I like them, I'll probably order another set with summer tires.

Am I correct in understanding that Audi uses an indirect system - in lieu of sensors - to monitor TPMS? I'll post some pics of the set up after the wheels get powder coats, tires get mounted , and the entire deal is installed.

[Lusky]

I think he was actually inferring that your wheel would flex and somehow contact the brake caliper under strenuous driving... based on the cardboard reference.

:shrug:

Sent from my SM-G950U1 using Tapatalk

It’s more clearance than stock wheels iirc so can’t see how they would move nor hit


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[wildtouch83]

my itchy finger hasn't pulled the trigger on wheels yet...not sure if I want to now or wait until after winter is over.

#firstworldproblems

[ormandj]

I just put my winters on, these have a 45mm offset so I had to use 5mm spacers in front. But good enough for winter. Gives me time to find the right Gloss Black wheels for summer. https://uploads.tapatalk-cdn.com/20171027/c7a9346b2a202a638a5c076646133143.jpghttps://uploads.tapatalk-cdn.com/20171027/dfd75d0075d92c9cb5e930f73b70df80.jpg

Sent from my SAMSUNG-SM-G920A using Tapatalk

What wheels/specs tires/specs so this is useful for future wheel and tire purchasers? Looks great!

[Cream]

What wheels/specs tires/specs so this is useful for future wheel and tire purchasers? Looks great!Well these are VMRs, 19x9.5. 45mm with 255/35 tires. I think there 35 offset wheels would fit without spacers

Sent from my SAMSUNG-SM-G920A using Tapatalk

[Mops@Nemesis]

Those look great. VMR actually has a killer sale right now. I just grabbed a set of V705 for my B9.

http://www.audizine.com/forum/showthread.php/787432-Winter-Wheel-Tire-Packages-MASSIVE-Discounts-Limited-Quantities!

[ormandj]

Neuspeed RSe102 19x9 +45, Michelin PS 4S 255/35R19. No fitment issues at all, just running 66.5mm to 57.1 aluminum hub centric rings.

https://lh3.googleusercontent.com/XDiDWRv5AOVhF--dESEXuoNAfHoR38Jp6x7erfTIAMN5d83jjTeWaAPdE2wXgiCT4 tIDo0R-gOWlGBbDTPIK7aT2vKn8GICHl3P73TMnv0jaOzEjdgxg46dTND PDqfNPbk3C8zx-4q7oKalVln2TxbwHFE8l5rkb9N35ga33GcNS1Qx-a33rrSmYNpMoKEYy8J0aBkhb-fw01AVV7oRxgjng-z-PO3z6SEYa5NAf0XWFTSf6OEyJfgcEkJf67tHqj6dHz8I14wBn8 gqPRutncTTLjyGX6w37dGgvKx6Y6nnNKUi8LiA8JzogCNyajv0 5_DKQ9RZGGXCK4bxbUa4xgeWA5fvFsMLnzqpszopq-Cv9-DtxbgJCww42fWMF1Ln6pFu6NoBhQifi_sSrskO5d23ZVTjqdGJ s5eGsIO7Zoe_h5tObj8ppEIrZUouQKaCT3w0h6ONR0nVemJuC8 u1LVTYGsb-edS-9m6PmX9QYR1wJbk0CEkU5SkbuDx5YljJlyHIDeV9V3ajKKgKvt N4gtL7Dy88ihYBnN_rjW65WEkpnptE6WrtzNl4PnfSrvNV4nbP zHHIo5cF2hzFr8zrWV3v23K_c3DmFpd-zWcdCed0=w1920-h907-no

[sciblades]

Did you need a hub centric rings? I ordered some nuespeed as well or is it just that model?

Sent from my SM-G955U using Tapatalk

[mossback]

Did you need a hub centric rings? I ordered some nuespeed as well or is it just that model?

Sent from my SM-G955U using Tapatalk

they come with hub rings by default.

[ormandj]

they come with hub rings by default.

They come with plastic rings, I purchased aluminum and used anti-seize since I track my car. sciblades: you definitely should be using hub centric adapter rings.. You may get it centered without due to the conical lug recesses, but you'll always have it centered properly with the rings. Worth a few bucks.

[mossback]

They come with plastic rings, I purchased aluminum and used anti-seize since I track my car. sciblades: you definitely should be using hub centric adapter rings.. You may get it centered without due to the conical lug recesses, but you'll always have it centered properly with the rings. Worth a few bucks.

I track the shit out of my car (10-20 times a year), the plastic rings are just fine. I didn't know you can get aluminum rings, but at least for me, they are unnecessary.

[ormandj]

I track the shit out of my car (10-20 times a year), the plastic rings are just fine. I didn't know you can get aluminum rings, but at least for me, they are unnecessary.

It probably depends on the plastic. I've had bad luck in the past with them cracking/melting to the hub. Never on Neuspeed wheels, though, so theirs may be a non-issue.

[mossback]

I guess so, the plastic is high temp stuff! It looks fine even when the wheels are hot, having swapped from wets to dry wheels at the track the rings still have there normal shape, no melted bits.

Im running 2 piece rotors so maybe that helps but am also running race pads, the aluminum hats have discolored from the temps but the plastic is just fine. Actually pretty amazing if you think about it. Now I am curious, will ping Nuespeed and ask about the rings they use.

[TheBigFish]

Where did you source your hub centric rings? TSW says their center bore is 72mm for this wheel. I can find 72.2mm to 57.1mm rings but not 72mm on the nose.


Yes had them powder coated gloss black to match the black optics

https://uploads.tapatalk-cdn.com/20171026/354e5d6722ee92dbaf941e7b7cabe9fd.jpg


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[TroySico]

The 19x9.5 ET45 pictured below. I actually just got mine and snapped these. Not sure on tire size, but I can check. These list at $5K. The 19x8.5 ET42 would work too, but spacers may be wanted for the correct look. I think I would run 8mm spacers personally.

https://farm5.staticflickr.com/4462/37696249236_ca8ddd9513_o.jpg (https://flic.kr/p/Zr68zE)IMG_7040 (https://flic.kr/p/Zr68zE) by Audiyos (https://www.flickr.com/photos/91999203@N06/), on Flickr

https://farm5.staticflickr.com/4494/37486615200_868df35454_o.jpg (https://flic.kr/p/Z7yGFJ)IMG_7033 (https://flic.kr/p/Z7yGFJ) by Audiyos (https://www.flickr.com/photos/91999203@N06/), on Flickr

https://farm5.staticflickr.com/4496/37696255366_816e046687_o.jpg (https://flic.kr/p/Zr6apm)IMG_7037 (https://flic.kr/p/Zr6apm) by Audiyos (https://www.flickr.com/photos/91999203@N06/), on Flickr

https://farm5.staticflickr.com/4498/37486613330_0883dd4be9_o.jpg (https://flic.kr/p/Z7yG8u)IMG_7035 (https://flic.kr/p/Z7yG8u) by Audiyos (https://www.flickr.com/photos/91999203@N06/), on Flickr

https://farm5.staticflickr.com/4509/37486616460_06dcde2fbc_o.jpg (https://flic.kr/p/Z7yH4s)IMG_7028 (https://flic.kr/p/Z7yH4s) by Audiyos (https://www.flickr.com/photos/91999203@N06/), on Flickr

https://farm5.staticflickr.com/4508/37696252736_5993d4a78a_o.jpg (https://flic.kr/p/Zr69C1)IMG_7039 (https://flic.kr/p/Zr69C1) by Audiyos (https://www.flickr.com/photos/91999203@N06/), on Flickr

@mops:

Looks like BBS offers a 19x9 et52 in the FS now! Is that the way to go on a TTRS? Or will the spokes not clear the caliper as far as you know? I love that they offer the oem size/offset - so rare.


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[Mops@Nemesis]

@mops:

Looks like BBS offers a 19x9 et52 in the FS now! Is that the way to go on a TTRS? Or will the spokes not clear the caliper as far as you know? I love that they offer the oem size/offset - so rare.

Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

I'll email BBS now and found out. I'll report back to you by EOD Monday. That is my favorite spec. Completely flat face. These wheels are made for the mk7/8v so I'm thinking you're good with that spec.

👍🏼

[ormandj]

Got the RSe102s in 19x9 +45 mounted. Michelin PS 4S in 255/35R19. Waiting on the Audi center caps to arrive but until then:

https://lh3.googleusercontent.com/QRJkbFdK0Enks5YzCjDsV-SQ_2Y7XgPQszV_GWsN6nme1KwiQ4BVu90Nj006XWKKhXCnu6kw Py_s6UFOtRz699E8ldprFI0GvNaNq-NJGAaxKnU8kCKW-Y8luQd2W8J8rsr7SgcIp31pmrtn1LdfYtJo74Gs8WEehAKzhwA NrHC0eNhUSoq2pI8q78_Np70IEzmgddokFk8vPq0fe5NmQoGeB UF7nVgHv9nvUKHr0BH5_LJLZe74JG8GsHjhTE78RGT4dBkEAAD klLh0j7qj_kNvCe9JKZNQKmpr0jFAW6mx_35LqaH8QO4Of_6rL MJV6G1fdFCUSd0KoYz576NHCuzRnAlvkKaXqfTp7m4f1wlaW6_ upg5tReA64ckK_vLmS9Tf-fOMcaF8xXpoP19mKVwax3CXbJSgihA7sDQVNuKys9TS2VFuw6g v7gWZmJeLRY3tSmVqlqJ6j1e_u41Q4klw7kFmNC2vcphClj65S 1PuLGZ1o9hlrOAB5q_9ijT0C0RYR4YkjtrRBInRuIlD_ObKD7n 29KsSZcLo-bfP7wTF7u-W8l8FhrbLVALi7TpygIsLDb2op0G3P8FUK9EPX3PgNg0CBeb6o 7-4aHwQUbRbuN2MevDgOPAQqGcoLGcXOZ51AIjSxRKpqzi-QbUvldW3C8VrW5w6KzI=w1299-h974-no

The wheels color shift depending on lighting.

Daytime: https://lh3.googleusercontent.com/YrEK5hzzzJG8hSFmpzoxcSYRcn-9O_tVdHQGhjDOKCej2k0-WXWY1TR4nI9sUpKJkqXOHS7nOVvqYCR6z4PtHpPYoJ9T8h2Ml1 RdOqDwnipwK2kbXAafM7ToXUTc62hVM0ZC7cH3DO-lgqOzx61_W4JoiLjPNXgZ2_mw4CGPyanwvdBnAC8xJsNbvaQiI M28pczGx2_ABH5S5D0kLLDUaup8umGdHO34iqqNYTmAbp3qlcS vvsOGNgh7ZfQhXJTATQ7Sgm8Bou2zl8MY_nvumKkgBLddUpP1W a5U_PzdTe4y75QIHH32uDTljymQtpdOHzkPxMl49ujCUDp_BdW DvIRt4fO-FHboLFkQzm_vWi4TtcxJPirpXMJJFqKZbxutMagX5vVyUw9j-GEMXOjQF1GwpII8LICGg_Sqc4XGzicc_Qd7tsYERmhoeKtqtY8 3yqcTbi7Eqk6lTZdHivgiED3-z2wBQmtugHPcPSX1uhyhXDJVgDN-U5XS-yoHjxWigVJIseS1Gl8nUw7AYW8w_xiYwULJ0HRUsShqmYftRTU ZyjxsVlZeXod-Icy5f5MBbK8QLpM2fKZ24cSvXGTXyeJ-luyjG71N73xzrE9zDOtdioz6EG2mkJFzGDtvJ9uAg851E7CCl_ wBR_1RfRUhwcsJ9EO8BSFtylY=w1299-h974-no

[Mops@Nemesis]

@mops:

Looks like BBS offers a 19x9 et52 in the FS now! Is that the way to go on a TTRS? Or will the spokes not clear the caliper as far as you know? I love that they offer the oem size/offset - so rare.

Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

Troy - BBS said the et52 would require 10mm spacers. The correct/no spacer TTRS fitment is the 19x9.5 ET45 pictured above.

Please let me know what else I can do.

[Lusky]

Troy - BBS said the et52 would require 10mm spacers. The correct/no spacer TTRS fitment is the 19x9.5 ET45 pictured above.

Please let me know what else I can do.

I run 18x9.5 et53 and 275/35’s. I would have poke out in the front if et45


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[TheBigFish]

I run 18x9.5 et53 and 275/35’s. I would have poke out in the front if et45


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

Where did you get your hubcentric rings for those Interlagos wheels?

[TroySico]

Troy - BBS said the et52 would require 10mm spacers. The correct/no spacer TTRS fitment is the 19x9.5 ET45 pictured above.

Please let me know what else I can do.

Damn! I’m running that on some
FF01s now and it’s too much poke with 9.5 and et45 [emoji24]

I may stick to ET52 and see if 5 or 7mm spacers work to get an effective 47 or 45 offset whilst staying with 9” width.

This likely is due to the spoke contact near the hub of the huge (too big) 8pot caliper


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[Mops@Nemesis]

Damn! I’m running that on some
FF01s now and it’s too much poke with 9.5 and et45 [emoji24]

I may stick to ET52 and see if 5 or 7mm spacers work to get an effective 47 or 45 offset whilst staying with 9” width.

This likely is due to the spoke contact near the hub of the huge (too big) 8pot caliper

Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

Good plan. Pushing outward is easy.

And yes, that caliper is dated and overly chunky :/

The 9" ET52 is totally flat. Seems like it could work for sure. It would be awesome if we could send you one to test fit.

[sciblades]

I did a 18×9 et45 and it is quite flush I'll grab some pictures tomorrow

Sent from my SM-G955U using Tapatalk

[TroySico]

Good plan. Pushing outward is easy.

And yes, that caliper is dated and overly chunky :/

The 9" ET52 is totally flat. Seems like it could work for sure. It would be awesome if we could send you one to test fit.

Do you have photos of flat et52 9” vs the one pictured above? The one above looks pretty flat to me! Lol! You can IM me and I’ll tell you more.


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[Mops@Nemesis]

Do you have photos of flat et52 9” vs the one pictured above? The one above looks pretty flat to me! Lol! You can IM me and I’ll tell you more.

Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

On it!

[Mops@Nemesis]

Do you have photos of flat et52 9” vs the one pictured above? The one above looks pretty flat to me! Lol! You can IM me and I’ll tell you more.

Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

BBS re: ET52...

We did not import that one and don’t really plan to.

[Mops@Nemesis]

Coming soon! 😎

HRE P101 in 20x9.5 satin black with carbon caps - min concave front, medium rear on 265/30 on this Exclusive TTRS in Porsche Grey Black.

https://farm5.staticflickr.com/4543/38630607416_9828f2f532_o.jpg (https://flic.kr/p/21RDXHs)Audi TT RS Coupé (https://flic.kr/p/21RDXHs) by Audiyos (https://www.flickr.com/photos/91999203@N06/), on Flickr

[wildtouch83]

Looking Sharp!!

Sent from my SM-G950U1 using Tapatalk

[nothau]

Rotiform KPS’s 19x8.5 ET45 with 245/35 PSS’s. I had to use a 15mm spacer for the fronts and a 12.5 in back, slight poke, but the look is growing on me.

Keeping my OEM 20x9 on 255/30 pirellis in case I have a fast and windy road to drive.

[nevetS4]

This is my winter setup: Niche Form -M158 Bronze 19x8.5 et34 with Michelin PA4 245/35-19.
I am using the 66.6-57.1 hub centric rings as this is a used set from S4. No spacer needed.

https://uploads.tapatalk-cdn.com/20171129/7eae05329a84acad999649febb728977.jpg


Sent from my iPhone using Tapatalk

[wildtouch83]

Coming soon! 😎

HRE P101 in 20x9.5 satin black with carbon caps - min concave front, medium rear on 265/30 on this Exclusive TTRS in Porsche Grey Black.

https://farm5.staticflickr.com/4543/38630607416_9828f2f532_o.jpg (https://flic.kr/p/21RDXHs)Audi TT RS Coupé (https://flic.kr/p/21RDXHs) by Audiyos (https://www.flickr.com/photos/91999203@N06/), on Flickr


Can't stop staring...

[Mops@Nemesis]

Hey guys - Figured I'd post up as I'm selling my BBS FS from my S4, and the spec happens to be the TT/TTS/TTRS fit.

19x9.5 ET45 in Diamond Black.
Wheels - $3,750 plus 50/50 ship split
Very low miles and minty. Wheels are $5,200 new. 20 pounds.


https://farm5.staticflickr.com/4462/37696249236_c2aadd5397_k.jpg (https://flic.kr/p/Zr68zE)IMG_7040 (https://flic.kr/p/Zr68zE) by Nemesis Autosport (https://www.flickr.com/photos/91999203@N06/), on Flickr

https://farm5.staticflickr.com/4508/37696252736_d8b84006fa_k.jpg (https://flic.kr/p/Zr69C1)IMG_7039 (https://flic.kr/p/Zr69C1) by Nemesis Autosport (https://www.flickr.com/photos/91999203@N06/), on Flickr

[Suzqttro]

So are these wheels fit and do not require spacers? After a nightmare with my old dealer and my A4, I will never use spacers again.

Sent from my VS995 using Audizine mobile app (http://r.tapatalk.com/byo?rid=87676)

[Mops@Nemesis]

So are these wheels fit and do not require spacers? After a nightmare with my old dealer and my A4, I will never use spacers again.

Sent from my VS995 using Audizine mobile app (http://r.tapatalk.com/byo?rid=87676)

They do not require spacers. More so than any other, BBS is function over form. That is the reason you must go to at least 10" before you see much concave with BBS.

[TRZ06]

That looks great, however not many tire options. No extreme performance category options for this size.


Coming soon! 😎

HRE P101 in 20x9.5 satin black with carbon caps - min concave front, medium rear on 265/30 on this Exclusive TTRS in Porsche Grey Black.

https://farm5.staticflickr.com/4543/38630607416_9828f2f532_o.jpg (https://flic.kr/p/21RDXHs)Audi TT RS Coupé (https://flic.kr/p/21RDXHs) by Audiyos (https://www.flickr.com/photos/91999203@N06/), on Flickr

[Rapture]

That looks great, however not many tire options. No extreme performance category options for this size.

Thanks, they have Michelin Pilot Sport 4S installed on them, Max Performance summer tire. Should be delivered next week. Unfortunately no car to mount them on yet.

[TRZ06]

While I have heard good things about the 4S tires, any aftermarket wheels should have extreme performance tire options like the Advan Neovo 08r or the Poteanza RE-71r. I think a better option is the same wheel as a 19" and a 35 series tire. That gets you better tire options.


Thanks, they have Michelin Pilot Sport 4S installed on them, Max Performance summer tire. Should be delivered next week. Unfortunately no car to mount them on yet.

[Rapture]

While I have heard good things about the 4S tires, any aftermarket wheels should have extreme performance tire options like the Advan Neovo 08r or the Poteanza RE-71r. I think a better option is the same wheel as a 19" and a 35 series tire. That gets you better tire options.

This really depends on what you are trying to achieve with a wheel/tire combo. If you are Track focused versus Street driving you’d probably consider different factors. For me this is the best choice.


Rapture

[chasiu]

Does anyone know how much clearance we have with the OEM wheels (20x9 et52) with the inner suspension? Looking to get a set of wheels that would be 5.7mm closer to the suspension compared to the OEM wheels. Car hasn't arrived yet so I can't take a look myself.

[Cale262]

The winter setup, 19x9ET38 OZ RACING RALLY. Tires are Pirelli Ice Zero studded, 225/45R19. This setup is a little heavier but "winter" [drive]


https://photos.smugmug.com/-18-Audi-TT-RS/n-3Knz2D/i-fzHSjLb/0/85d82910/X5/i-fzHSjLb-X5.jpg

https://photos.smugmug.com/-18-Audi-TT-RS/n-3Knz2D/i-Nf5BpDf/0/74df55f9/4K/i-Nf5BpDf-4K.jpg

[mossback]

Wait, is that photo on 265/35-18 or 255/40-18?

265/35 - 18"

[audibmi]

Spring sneakers until I figure out what to do for summer.

BBS CI-R 19x9 et42mm Platinum Silver
Michelin Pilot Sport 4S 255/35/19
Machined Brushed Aluminum BBS center caps
Stock suspension height

The open spoke design showcases the red calipers nicely.

https://i.imgur.com/uozPCsz.jpg
https://i.imgur.com/FkGGx1M.jpg

[Chuckster]

Looks really good. Any wider angles?

[audibmi]

wider angle, zoomed out:

https://i.imgur.com/PyEvotH.jpg

[Chuckster]

Thank you. Those look great!

[allen_petty]

70756
Found my winter setup. Enkei 19 X 8.5 et42 with Michelin Alpin PA4 tires 245/35R19

[Cbhoy24]

I'm looking to change the Pzero's on my 2018 TTRS but I'm not really a fan of aftermarket wheels, I like the stock look.

I'm also running APR Stage 1 and the Pzero's are even more garbage than I ever thought they were when it was stock. I can't use full throttle launch control at all on them. I'm looking into swapping them out for Michelin PS4's and although they do size 255/30/20, I was thinking about the 255/35/20 tyres to give me a larger sidewall to help increase LC traction. There isn't a lot of give /crumple in a 30 tyre.

My question is, would increasing the 30 aspect ratio to 35 be okay, I realise the ride height would probably increase?

If not, I may opt for a set of "track" wheels for the dragstrip, I'm guessing dropping down to 19 or even 18 and increasing the sidewall height on PS4's would let me at least use full launch control?

[sciblades]

I'm looking to change the Pzero's on my 2018 TTRS but I'm not really a fan of aftermarket wheels, I like the stock look.

I'm also running APR Stage 1 and the Pzero's are even more garbage than I ever thought they were when it was stock. I can't use full throttle launch control at all on them. I'm looking into swapping them out for Michelin PS4's and although they do size 255/30/20, I was thinking about the 255/35/20 tyres to give me a larger sidewall to help increase LC traction. There isn't a lot of give /crumple in a 30 tyre.

My question is, would increasing the 30 aspect ratio to 35 be okay, I realise the ride height would probably increase?

If not, I may opt for a set of "track" wheels for the dragstrip, I'm guessing dropping down to 19 or even 18 and increasing the sidewall height on PS4's would let me at least use full launch control?I would not suggest going with a bigger aspect ratio giving the gear shifts are based on wheel speed..

Sent from my SM-N950U using Tapatalk

[MattRG]

I would not suggest going with a bigger aspect ratio giving the gear shifts are based on wheel speed..

Sent from my SM-N950U using Tapatalk

That's the first I have heard of that. I know quite a few folks who are running 255/35/20's and have for some time. I know it makes the speedometer display a little bit off (75mph displayed would be more like 78mph actual) but I have never heard that it would effect the transmission logic.

[Chuckster]

That's the first I have heard of that. I know quite a few folks who are running 255/35/20's and have for some time. I know it makes the speedometer display a little bit off (75mph displayed would be more like 78mph actual) but I have never heard that it would effect the transmission logic.

As long as the front and rears are equal and within 3% of oem diameter, I wasn’t aware of issues aside from the speedo being slightly inaccurate.

[wildtouch83]

has anyone gone to a slightly more narrow wheel from the stock 20x9? I want to go down to 19s and I found a set that I like. However, they are 19x8.5. I don't track my car or anything, so I'm not concerned there.

I am just trying to weigh out any cons there might be and thought this would be a good place for feedback.

[XLR8 Craig]

Just wanted to chime in quick here!

We recently installed a set of ABT GR-20s on a 2018 TT-RS

They were 20"x9" et37 and they looked right at home!

https://farm2.staticflickr.com/1803/42626875035_1a01caa338_c.jpg

https://farm2.staticflickr.com/1761/29660106248_2e21c0c71c_c.jpg

If anyone is interested in a set of ABT wheels feel free to send us a PM for pricing!

Happy modding!

[rblauson]

Just wanted to chime in quick here!

We recently installed a set of ABT GR-20s on a 2018 TT-RS

They were 20"x9" et37 and they looked right at home!

https://farm2.staticflickr.com/1803/42626875035_1a01caa338_c.jpg

https://farm2.staticflickr.com/1761/29660106248_2e21c0c71c_c.jpg

If anyone is interested in a set of ABT wheels feel free to send us a PM for pricing!

Happy modding!

This my car and my ABT wheels.
XLR8 is correct. I love them.
Mark


Sent from my iPad using Audizine (http://r.tapatalk.com/byo?rid=87676)

[MattRG]

This my car and my ABT wheels.
XLR8 is correct. I love them.
Mark


Sent from my iPad using Audizine (http://r.tapatalk.com/byo?rid=87676)

Those do look fantastic. I will put them on my list of possible replacements for my OEM 20's down the road.

[wildtouch83]

Super happy with the Neuspeed rse102 in gloss black. 19x9 et40 wrapped in Michelin Pilot Sport 4S 255-35/19

https://i.imgur.com/UYTul8t.jpg

https://i.imgur.com/mRH0BSK.jpg

[natetheskate]

Super happy with the Neuspeed rse102 in gloss black. 19x9 et40 wrapped in Michelin Pilot Sport 4S 255-35/19

https://i.imgur.com/UYTul8t.jpg

https://i.imgur.com/mRH0BSK.jpg

Looks great! What offset are these? ET40? ET45? I am looking at ordering the RSe10's but want to make sure they clear the caliper.

[Chuckster]

He says et40 right after the wheel size.

[natetheskate]

He says et40 right after the wheel size.

Apparently I can't read... [cool]

[StraySheep]

Niche misano m116 19x8.5

Nitto Invo 255/35/19

They also offered this model in 20'' but since im lowered, clearance could of been an issue

Wheels look great. What's the offset?

[Chiraoka]

wider angle, zoomed out:

https://i.imgur.com/PyEvotH.jpgAny spacers needed with your setup ?

Sent from my SM-G9650 using Tapatalk

[audibmi]

Any spacers needed with your setup ?



no spacers as pictured.

[nefkntym]

Super happy with the Neuspeed rse102 in gloss black. 19x9 et40 wrapped in Michelin Pilot Sport 4S 255-35/19

https://i.imgur.com/UYTul8t.jpg

https://i.imgur.com/mRH0BSK.jpg

Did you special order these in gloss black? I am seeing this in satin black. Did you order these straight from Neuspeed or did you use a different vendor? I am asking because direct usually yields a higher price.

[wildtouch83]

Did you special order these in gloss black? I am seeing this in satin black. Did you order these straight from Neuspeed or did you use a different vendor? I am asking because direct usually yields a higher price.

I lucked out and found a local buyer who was selling. Everywhere I looked online for these in gloss black had them backordered.

[nefkntym]

I lucked out and found a local buyer who was selling. Everywhere I looked online for these in gloss black had them backordered.

For your 19x9 et40 wheels, did you have to use spacers at all to clear the calipers?

[wildtouch83]

Nope, no spacers required.
For your 19x9 et40 wheels, did you have to use spacers at all to clear the calipers?

Sent from my Pixel 2 using Tapatalk

[BeTTo RS]

Does anybody knows if there are BBS CH-RII that are a different application for theTT RS MKIII? I checked with a Dealer in the US and told me that not.

Thanks!

[BeTTo RS]

Would love to see some pics of TT RS on R8’s wheels?

[nefkntym]

Would love to see some pics of TT RS on R8’s wheels?

It would be the front wheels of the R8. They won't have enough load rating for the TTRS.

[BeTTo RS]

It would be the front wheels of the R8. They won't have enough load rating for the TTRS.

Thanks! Is it because of the car’s weight distribution, being it’s a mid engine car, not that heavy on the front!

[KiddJoey]

20x9 et35 OZ Racing Leggera HLT
Gloss black finish
Stock tires Yokohama Advan 255/30ZR 20
MSS Sport 3/4” set drop (5/8” current drop w/1000 miles expecting another 1/8” drop)

84028
84029
84030


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[nefkntym]

20x9 et35 OZ Racing Leggera HLT
Gloss black finish
Stock tires Yokohama Advan 255/30ZR 20
MSS Sport 3/4” set drop (5/8” current drop w/1000 miles expecting another 1/8” drop)

84028
84029
84030


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

Can you post a side profile pic of your car? I almost ordered a set of these yesterday afternoon. Thanks in advance.

Looks good!!

[KiddJoey]

Can you post a side profile pic of your car? I almost ordered a set of these yesterday afternoon. Thanks in advance.

Looks good!!

84033



Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[KiddJoey]

84033



Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

Better lighting.
84045


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[BeTTo RS]

If I'm not mistaken, when you get the dynamic package w/ the ceramics you automatically get the 20x9 ET52 wheels.

Mine came with 19”X9”, but I haven’t pulled the wheel out to check the ET.

[TroySico]

I’ve been bad and not sharing!

Two set ups:

Track: Forgeline GS1R in 19x9 et45 with Michelin PSC2 in 265/35R19. Requires 3mm spacer in front.


Daily/Wet Track: BBS CI-R 19x9 ET42 with Michelin PS4S in 265/35R19

Car is on 034Motorsport Dynamic+ Springs along with all other 034 bolt ons including Camber Mounts enabling -2.4 camber up front!


86915
86916
86917
86918
86919
86920






Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[TwistRate]

^ where are you purchasing your spacers from? I think the forgeline looks fantastic. Can you provide your opinion on the PSC2 performance comparing them to any other R comps?

[twin_turbo]

Tire Rack is stating that a 19x8 wheel with 35mm offset will fit the TT RS. Can anyone confirm that this will clear the calipers? Seems that most are running 40 to 45mm offset. Thanks in advance.

[Stevos555]

Anyone know of a track wheel that fits ceramics?


Sent from my iPhone using Tapatalk

[nefkntym]

Neuspeed RSE102 19x9 ET40 will not fit CCB without a spacer. I am currently trying to find a quality 3mm spacer. So far I am having trouble in that area.

[Stevos555]

is there a known aftermarket wheel that fits over ceramics? Need a set of track wheels to beat on.


Sent from my iPhone using Tapatalk

[sciblades]

Any 9inch et45

Sent from my SM-N960U using Tapatalk

[Cream]

Neuspeed RSE102 19x9 ET40 will not fit CCB without a spacer. I am currently trying to find a quality 3mm spacer. So far I am having trouble in that area.APR now has spacers and they do 1, 2, 3, etc

Sent from my SAMSUNG-SM-G920A using Tapatalk

[nefkntym]

That doesn’t make sense, 45 is 5 mm closer than 40. I have 40 that doesn’t quite clear. Ultimately it is going to be on spoke design.

[nefkntym]

APR now has spacers and they do 1, 2, 3, etc

Sent from my SAMSUNG-SM-G920A using Tapatalk

I tried that/them, I am still looking for a quality spacer. I got 3 sets of 3mm, all 6 of them were like this...

https://farm2.staticflickr.com/1940/43414299510_c9239a1213_h.jpg

https://farm2.staticflickr.com/1904/43414300270_3710803c8c_h.jpg

[TwistRate]

Semi on topic.... for those of you running spacers how thick of a spacer can you run with the standard 14x1.5 (27-30mm) lug bolts? Also is there a hardened lug bolt that is preferred? On other platforms I would be replacing the OEM studs with ARP hardware but that does't seem to be a popular choice with Audi owners.

I understand I can get generic lug bolts on ebay, amazon and from some vendors but when possibly running a thicker spacer I'd really like to have top shelf lug bolts. Can anyone steer me in the right direction?

For example ... how do I know THESE (https://www.uspmotorsports.com/Conical-Seat-Wheel-Bolt-Black-14x1.5x-27mm-Length-20-Pack.html) are any good?

[DannyLo]

Winter Wheels are on my TTRS.

18x8 Rial Kodiak et31 and 235/45R18 Goodyear Ultra Grip WRT (not pictured)

Super cheap, made in Germany, and clear steel brakes with no spacers! Have put 200 miles on them already and they ride great.

https://i.imgur.com/UH2iAmG.jpg

https://i.imgur.com/WEPG04h.jpg

[Huey52]

Rial are excellent wheels. I've been running them in Winter for 7 years with Michelin Alpin tires. Similar rim build process and quality as Audi OEM.

[Malibu72]

Ok fellow TT RS owners, I am getting ready to pull the trigger on track prep parts (wheels, brakes, etc), and was hoping I could get y’all to weigh in on my plans and see if everything will work.

Wheels: neuspeed rse102’s 20x9 40mm offset, reuse oem tires (255/30/20) and then move to ps4s in stock size. Later, pick up same wheel but in 19x9 40mm offset and run sport cup2s in 255/35/19 as dedicated track set up and run the 20’s as street wheels.

Brakes: am ordering Essex/ap racing bbk at the same time as the 20” neeuspeeds above (ie now). Leaning towards the 9660 set up since it’s for hpde and the 9668 seems like overkill. This brake setup will open up more fittment options and I also want to preserve the oe wheels and brakes instead of trashing them.

Goal is no spacers needed with the above (pls weigh in if I’m wrong on that) at stock height with 034 front camber plates installed (-2.4 deg) and oe rear suspension. Also, will I still be good when I lower the car on 034 springs (0.8” drop front/0.6” drop rear) and include adjustable rear toe links and upper control arms setting to around -1.3 to -1.5 deg camber out back.

Will above suspension setup work with both wheel option I mentioned with no spacers and no rubbing?

Thanks in advance!

[Metlhd]

I’ve been bad and not sharing!

Two set ups:

Track: Forgeline GS1R in 19x9 et45 with Michelin PSC2 in 265/35R19. Requires 3mm spacer in front.


Daily/Wet Track: BBS CI-R 19x9 ET42 with Michelin PS4S in 265/35R19

Car is on 034Motorsport Dynamic+ Springs along with all other 034 bolt ons including Camber Mounts enabling -2.4 camber up front!


86915
86916
86917
86918
86919
86920






Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

DUDE, looks like a GREAT tack day event !!! Are you in the process of setting up a pass coming down the Corkscrew or are you just way off line ;)

[big residual]

Ok fellow TT RS owners, I am getting ready to pull the trigger on track prep parts (wheels, brakes, etc), and was hoping I could get yÂ’all to weigh in on my plans and see if everything will work.

Wheels: neuspeed rse102Â’s 20x9 40mm offset, reuse oem tires (255/30/20) and then move to ps4s in stock size. Later, pick up same wheel but in 19x9 40mm offset and run sport cup2s in 255/35/19 as dedicated track set up and run the 20Â’s as street wheels.

Brakes: am ordering Essex/ap racing bbk at the same time as the 20” neeuspeeds above (ie now). Leaning towards the 9660 set up since it’s for hpde and the 9668 seems like overkill. This brake setup will open up more fittment options and I also want to preserve the oe wheels and brakes instead of trashing them.

Goal is no spacers needed with the above (pls weigh in if I’m wrong on that) at stock height with 034 front camber plates installed (-2.4 deg) and oe rear suspension. Also, will I still be good when I lower the car on 034 springs (0.8” drop front/0.6” drop rear) and include adjustable rear toe links and upper control arms setting to around -1.3 to -1.5 deg camber out back.

Will above suspension setup work with both wheel option I mentioned with no spacers and no rubbing?

Thanks in advance!

Why are you doing the rse102s in 20"? I get that you get to burn through your oem tires and then have 20" PS4s for daily, but I tripped over that logic personally. None of the oem tires are anything I'd want to deal with on track, and I'm not sure I'd want to daily 20" w/ stock suspension... but once you get into lowering it and dialing up suspension performance, it sounds like bad ride times and rub city.

It seems simpler to me to go straight for your 19" (or 18" if you know the Neuspeeds clear... I think the 102s do, most likely the 10s do, and there are TSW Interlagos as another stock clearing option in 18 to check out) setup with the track tires you want (check out RE71Rs as an SC2 option, Hankook RS-4s as a lesser but cheaper option too). Take your 20" stock wheels and tires off and put them in a box for when you sell. I'm biased bc that's what I did, but it just strikes me as less complicated and you don't waste any track days dealing with dodgy tires. :)

BBK. Doing a BBK in parallel with new wheels could lead to clearance problems, or at least low odds you won't be running spacers of some kind (which are not the end of the world if they're < 5mm). If you can get the template for the APs on your car and test fit barrel and spokes, you can avoid some problems. I like the AP kit Essex sells, but I ended up doing a Girodisc swap when I first got the car (rotors and pads, into the box for later). I recently put on Brembo's GT-S M6 calipers which are a bolt-on replacement for the stock calipers (and... into the box for the next owner). I think you can do front Girodiscs + M6s + SS lines for about $800-1000 less than the Essex kit. We won't count the $550 you should spend getting Pagid RS29s for pads in any scenario. I preferred the Brembo because it was monobloc and I already had rotors I like, but I don't think you can go wrong with either option. Ultimately, I think the stock calipers with swapped pads and rotors (front and rear) is good enough for most HPDE work, but the calipers are going to discolor if you care about that. Point being: I think you need to swap pads and rotors before getting serious on track, but you can do calipers later.

As far as your suspension options, I think you might have problems lowering with 20s. If you do the fixed camber plates, that may reduce fender-side rub risks, not sure about strut side. On mine w/ ET52 18" wheels (Forgestar CF-5) I cleared stock calipers and suspension, but strut clearance was tight. No rub. On 19" ET45 (HRE FF15), I cleared, but rub on full compression in the rear. On the suspension front, I did 6 days on stock suspension, no changes. Not bad. Soft, lack of camber up front killed some RE71Rs, but it wasn't a big issue. I've put coilovers on since then, but one thing I learned from my R and RS3, after doing lowering springs from VWR and MSS... you might as well just do coilovers. I get it, cancelers yikes, my beloved comfortable dynamic suspension... frankly, a good set of coilovers will handle bumps stiffly but comfortably, and once you start throwing on lowering springs and plates, you're might be making it worse than good coilovers. Yes, you have a switch at the end that makes your dampers softer or harder... but the rest of the geometry is a departure. If you are serious enough about being on track to need/want a BBK, you probably want to take off your magnets (and... put them in the box for the future owner of your car to enjoy!).

This is just my 2 cents... I have all sorts of scenario plans to fast forward to the end state all over my hard drive, but ultimately area by area seems to yield a higher hit rate than doing too many things en masse. No judgments at all, just my takes.

[DannyLo]

Thoughts on a 18x9.5 et30 in the rear...doable? Will it poke? Can some camber solve for it? I'm going to see if I can do some digging in the regular TT/TTS forum for some answers, because I wouldn't want to stretch if i can avoid it. I like my traction/handling. That's assuming the bodies are identical between these cars, which I believe they are.

I'm looking at a special set of wheels, and that spec above has the character I want for the rear of the car. I plan on running the same model wheel with a different spec (18x9.5 et45) in the front, which I know will be fine, but it doesn't have the face concavity that et30 one i mentioned earlier does. That's why i want it on the rear to add a dynamic look.

[big residual]

Thoughts on a 18x9.5 et30 in the rear...doable? Will it poke? Can some camber solve for it? I'm going to see if I can do some digging in the regular TT/TTS forum for some answers, because I wouldn't want to stretch if i can avoid it. I like my traction/handling. That's assuming the bodies are identical between these cars, which I believe they are.

I'm looking at a special set of wheels, and that spec above has the character I want for the rear of the car. I plan on running the same model wheel with a different spec (18x9.5 et45) in the front, which I know will be fine, but it doesn't have the face concavity that et30 one i mentioned earlier does. That's why i want it on the rear to add a dynamic look.

Doing an offset stagger seems like a high complexity price to pay for getting just the right wheel style you want. You won't be able to rotate front to rear, which is a big loss if you run directional tires. I get it, you want some dish in your life... but having negligible dish up front and some out back is a bit odd looking when I've researched it.

My take: it will poke by 15-20mm no matter what you do with camber, which isn't egregious but you'll notice. W/ 18s if you're not lowered you'll also have decent wheel gap. You'll be out just over 28mm from stock 20x9s, so the question is how much camber are you going to add and by what means. It looks like each degree of camber buys you about 7 mm offset on 18s. On stock, large gains would be 0.5-0.7 degrees of neg camber, which gets you about 5mm of tuck at the top. I think you still clear the strut inside, as you've moved out by 15mm with the wheel changes, so should be good. So you'd need a lot more camber to not be looking at 15-20mm of poke.

Me, I'd rock, the ET45s and never look back. Then again, I run ET45 19x9.5 (w/ no dish at all HRE FF15s) and it's fine, but it's just enough poke to catch my eye.

[DannyLo]

Doing an offset stagger seems like a high complexity price to pay for getting just the right wheel style you want. You won't be able to rotate front to rear, which is a big loss if you run directional tires. I get it, you want some dish in your life... but having negligible dish up front and some out back is a bit odd looking when I've researched it.

My take: it will poke by 15-20mm no matter what you do with camber, which isn't egregious but you'll notice. W/ 18s if you're not lowered you'll also have decent wheel gap. You'll be out just over 28mm from stock 20x9s, so the question is how much camber are you going to add and by what means. It looks like each degree of camber buys you about 7 mm offset on 18s. On stock, large gains would be 0.5-0.7 degrees of neg camber, which gets you about 5mm of tuck at the top. I think you still clear the strut inside, as you've moved out by 15mm with the wheel changes, so should be good. So you'd need a lot more camber to not be looking at 15-20mm of poke.

Me, I'd rock, the ET45s and never look back. Then again, I run ET45 19x9.5 (w/ no dish at all HRE FF15s) and it's fine, but it's just enough poke to catch my eye.

I have a shop with a mount/balance station, so the rotating part, although tedious, is most definitely doable.

That being said, you're probably right on the offset being a bit much. My winters are 18x8 et31 and they seem pretty flush, at least in front. These 19x9.5 at et30 would put them 20mm further out than even those.

I just needed a sanity check. I don't think the difference in face design will be something I'll wish for once the wheels are actually on the car. Cheers

[ItsRainingLead]

I have a shop with a mount/balance station, so the rotating part, although tedious, is most definitely doable.

That being said, you're probably right on the offset being a bit much. My winters are 18x8 et31 and they seem pretty flush, at least in front. These 19x9.5 at et30 would put them 20mm further out than even those.

I just needed a sanity check. I don't think the difference in face design will be something I'll wish for once the wheels are actually on the car. Cheers

I went with BC Forged and a non rotatable setup to get more concavity on the rear wheels. It may end up biting me, in respect to tire wear, but I wanted the aesthetic based on pictures that Paul Gi sent me.

I'm doing 19x9.5 et45 up front and 19x9.5 et42 in the rear with PS4S in 265/35/19, will lower with KW HAS springs and putting on a neuspeed rear sway and end links. It may see a track day or two, but mostly roads.

[Malibu72]

Why are you doing the rse102s in 20"? I get that you get to burn through your oem tires and then have 20" PS4s for daily, but I tripped over that logic personally. None of the oem tires are anything I'd want to deal with on track, and I'm not sure I'd want to daily 20" w/ stock suspension... but once you get into lowering it and dialing up suspension performance, it sounds like bad ride times and rub city.

It seems simpler to me to go straight for your 19" (or 18" if you know the Neuspeeds clear... I think the 102s do, most likely the 10s do, and there are TSW Interlagos as another stock clearing option in 18 to check out) setup with the track tires you want (check out RE71Rs as an SC2 option, Hankook RS-4s as a lesser but cheaper option too). Take your 20" stock wheels and tires off and put them in a box for when you sell. I'm biased bc that's what I did, but it just strikes me as less complicated and you don't waste any track days dealing with dodgy tires. :)

BBK. Doing a BBK in parallel with new wheels could lead to clearance problems, or at least low odds you won't be running spacers of some kind (which are not the end of the world if they're < 5mm). If you can get the template for the APs on your car and test fit barrel and spokes, you can avoid some problems. I like the AP kit Essex sells, but I ended up doing a Girodisc swap when I first got the car (rotors and pads, into the box for later). I recently put on Brembo's GT-S M6 calipers which are a bolt-on replacement for the stock calipers (and... into the box for the next owner). I think you can do front Girodiscs + M6s + SS lines for about $800-1000 less than the Essex kit. We won't count the $550 you should spend getting Pagid RS29s for pads in any scenario. I preferred the Brembo because it was monobloc and I already had rotors I like, but I don't think you can go wrong with either option. Ultimately, I think the stock calipers with swapped pads and rotors (front and rear) is good enough for most HPDE work, but the calipers are going to discolor if you care about that. Point being: I think you need to swap pads and rotors before getting serious on track, but you can do calipers later.

As far as your suspension options, I think you might have problems lowering with 20s. If you do the fixed camber plates, that may reduce fender-side rub risks, not sure about strut side. On mine w/ ET52 18" wheels (Forgestar CF-5) I cleared stock calipers and suspension, but strut clearance was tight. No rub. On 19" ET45 (HRE FF15), I cleared, but rub on full compression in the rear. On the suspension front, I did 6 days on stock suspension, no changes. Not bad. Soft, lack of camber up front killed some RE71Rs, but it wasn't a big issue. I've put coilovers on since then, but one thing I learned from my R and RS3, after doing lowering springs from VWR and MSS... you might as well just do coilovers. I get it, cancelers yikes, my beloved comfortable dynamic suspension... frankly, a good set of coilovers will handle bumps stiffly but comfortably, and once you start throwing on lowering springs and plates, you're might be making it worse than good coilovers. Yes, you have a switch at the end that makes your dampers softer or harder... but the rest of the geometry is a departure. If you are serious enough about being on track to need/want a BBK, you probably want to take off your magnets (and... put them in the box for the future owner of your car to enjoy!).

This is just my 2 cents... I have all sorts of scenario plans to fast forward to the end state all over my hard drive, but ultimately area by area seems to yield a higher hit rate than doing too many things en masse. No judgments at all, just my takes.

Thanks for the input. Came to some similar conclusions today as well. Went 19” wheels after speaking to neuspeed and they said it’d fit the ap bbk. Went with ap just bc of personal experience with the j hook rotors but like you said, no wrong answer there. I’ll probably end up with coil overs but I love my mag ride so for now I’m sticking with it.

Edit: wheels are rse102’s 19x9 +45mm offset. AP bbk 9660 clears stock wheels so should be okay according to both neuspeed and Essex. (Was burning up the phone lines today). I’ll post an update on here once everything is mounted up and confirm fitment.

[cantcatchtomm]

Rears are pretty even with the fender at 18x9.5 +53 with 275/35R18 RE71R tires. Even +45 would poke I’m guessing

107157

107158

107159


Stance will change when this finally gets here...

107166

[Dr Bill]

Rears are pretty even with the fender at 18x9.5 +53 with 275/35R18 RE71R tires. Even +45 would poke I’m guessing


107159




Nice. Which wheels?

[cantcatchtomm]

Nice. Which wheels?

TSW Interlagos. Following Lusky’s lead.

107343

[Paul@SupremePower]

Set of BC Forged KLS01 for a TTRS 8s customer:

19x9.5 +45 front
19x9.5 +42 rear

These weigh in around 19.1 each


http://i275.photobucket.com/albums/jj283/supremepowerparts/Allset/A2DA9ED8-3C10-4A33-A967-F43190F4EB1F_zpszkmbhmwd.jpeg (http://s275.photobucket.com/user/supremepowerparts/media/Allset/A2DA9ED8-3C10-4A33-A967-F43190F4EB1F_zpszkmbhmwd.jpeg.html)

[Jeff_Jeske]

I'm still trying to determine whether the OZ Ultra HLT in a 19x9.5 +40 running a 255/35/19 RE71R will fit without rubbing on the TTRS.

[Qwik23]

Set of BC Forged KLS01 for a TTRS 8s customer:

19x9.5 +45 front
19x9.5 +42 rear

These weigh in around 19.1 each


http://i275.photobucket.com/albums/jj283/supremepowerparts/Allset/A2DA9ED8-3C10-4A33-A967-F43190F4EB1F_zpszkmbhmwd.jpeg (http://s275.photobucket.com/user/supremepowerparts/media/Allset/A2DA9ED8-3C10-4A33-A967-F43190F4EB1F_zpszkmbhmwd.jpeg.html)19x9.5 fit on front?
That's a good looking set of wheels.

Sent from my Pixel 3 XL using Tapatalk

[Paul@SupremePower]

19x9.5 fit on front?
That's a good looking set of wheels.

Sent from my Pixel 3 XL using Tapatalk

They certainly do. With ease!

[Ross_T_Boss]

Just what I needed, some wheel porn [:D]

I'm thinking to go Neuspeed RSE102, been temped to go bronze to go with Panther Black. But I'm not keen on the matte. I don't think I can do wheels that aren't gloss finish, so Hyper Black it is...

I'm thinking 19" ET40, right now on stock 19s they sit too far inboard. I've got a set of 255/35 PS4S to go on, sitting about 5mm above min height on MSS Track pack, stock camber. Slightly temped to go ET45 with 8mm spacers for a bit more flush look, but don't want rubbing.

Anyone see issues with that?

I'm in the UK but looking to pick these up from my bro's place (West Coast) in May so need a supplier who can do be a good price ;)

[Malibu72]

Thanks for the input. Came to some similar conclusions today as well. Went 19” wheels after speaking to neuspeed and they said it’d fit the ap bbk. Went with ap just bc of personal experience with the j hook rotors but like you said, no wrong answer there. I’ll probably end up with coil overs but I love my mag ride so for now I’m sticking with it.

Edit: wheels are rse102’s 19x9 +45mm offset. AP bbk 9660 clears stock wheels so should be okay according to both neuspeed and Essex. (Was burning up the phone lines today). I’ll post an update on here once everything is mounted up and confirm fitment.


Update: got the Essex parts/AP 9660 bbk installed last week, obviously it clears the stock 20’s np. We test fit the neuspeed wheels as well and it easily clears them with even more room to spare; rse102’s 19x9 +45mm offset.

[BeTTo RS]

Daily/Wet Track: BBS CI-R 19x9 ET42 with Michelin PS4S in 265/35R19



I have the same specs for the wheels, but I have Michelin PS4S 245/35R19 with BBS’ 5 Mm spacers to get a flush look.

[Dr Bill]

Another data point.

Neuspeed RSE122 wheels fit fine. 18 x 9.5 ET45 with 265/35R18 RE71R tires.

[pferrar101]

I need some help figuring out what ET I can run on my TTRS. Some of the wheels I’m looking at on their websites say a 20X9 ET35 will fit but I’m skeptical. Any ideas on how I can confirm this?


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[Qwik23]

I need some help figuring out what ET I can run on my TTRS. Some of the wheels I’m looking at on their websites say a 20X9 ET35 will fit but I’m skeptical. Any ideas on how I can confirm this?


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)I've been using shops to help me with determining fit. And in some cases test fitting rims on the car. I've also called manufacturers to tak through sizing options. Or you luck 8ur with someone on IG running that setup to confirm. Stock ET on our 20s is 52 I think.

Sent from my Pixel 3 XL using Tapatalk

[pferrar101]

If you want a 9” width +35 is about flush in rear. I think it’s too much for the front though.

I’ve done a bunch of TTRS fitments shoot me an email and I’d be glad to help you out. 🤙

Will do thanks


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[Chuckster]

TTS, but same concern. These are 20x9ET35 HRE FF01’s paired with 265/30/20 P4S‘s. I’m lowered on MSS Kit streets. The rear rubbed until I removed the wheel well staples. The front is slightly more aggressive and isn’t ideal for track use. I’d be afraid to blow out the front fenders. If I went back down to stock 255’s, the sidewall is a little thin for hard driving. I think if you plan to do any track time, a 19” setup is more useable.

https://i.postimg.cc/K3ZjBwS7/122-ABFEB-FBEF-439-F-93-A3-9-EF3808-EDFBB.jpg (https://postimg.cc/K3ZjBwS7)

https://i.postimg.cc/z35VsbbL/C4-BA8-A36-1553-4-C8-D-BB16-E21-AE388512-A.jpg (https://postimg.cc/z35VsbbL)

https://i.postimg.cc/47RmNnWS/F927-B6-E6-234-C-47-E2-874-F-A521-A3-A0-B3-E8.jpg (https://postimg.cc/47RmNnWS)

[HHughes1]

TSW Interlagos. Following Lusky’s lead.

107343

You don't happen to know the weight of these wheels do you?

Never mind, I just noticed the picture and I see they are 20#s. Going to get a set of these

[cantcatchtomm]

You don't happen to know the weight of these wheels do you?

Never mind, I just noticed the picture and I see they are 20#s. Going to get a set of these

For track wheels they’re great. They do have small enough clearance to the caliper that rocks get stuck and scratch the barrel of the wheel. Sounds terrible and will go through the paint (my front wheels have a ring of silver where the rest of the barrel is black). Neuspeeds have a little more clearance it seems.

[Paul@SupremePower]

Litespeed Racing RS5

Magnesium Forged

15.98 pounds


19x9.5 +45 57.1 5x112 front
19x9.5 +42 57.1 5x112 rear

Toyo R888R 265/30ZR19


https://oi275.photobucket.com/albums/jj283/supremepowerparts/Allset/DC99C672-1960-4EBC-BCA8-AF9244ED0E98_zpseadkbwmq.jpeg (http://s275.photobucket.com/user/supremepowerparts/media/Allset/DC99C672-1960-4EBC-BCA8-AF9244ED0E98_zpseadkbwmq.jpeg.html)

https://oi275.photobucket.com/albums/jj283/supremepowerparts/Allset/4D209F20-4392-4178-92D8-DA1A4EDFD2B1_zpsubdfhbxq.jpeg (http://s275.photobucket.com/user/supremepowerparts/media/Allset/4D209F20-4392-4178-92D8-DA1A4EDFD2B1_zpsubdfhbxq.jpeg.html)

https://oi275.photobucket.com/albums/jj283/supremepowerparts/Allset/4D209F20-4392-4178-92D8-DA1A4EDFD2B1_zpsubdfhbxq.jpeg (http://s275.photobucket.com/user/supremepowerparts/media/Allset/4D209F20-4392-4178-92D8-DA1A4EDFD2B1_zpsubdfhbxq.jpeg.html)

https://oi275.photobucket.com/albums/jj283/supremepowerparts/Allset/AA092D89-CC7C-418B-9426-8342853D872B_zps3skbaapm.jpeg (http://s275.photobucket.com/user/supremepowerparts/media/Allset/AA092D89-CC7C-418B-9426-8342853D872B_zps3skbaapm.jpeg.html)

[Thumper3]

Nuespeed RSe10s in Dark Bronze - 19x9 ET40 with Pilot Sport 4S's 265/35/19


https://imagizer.imageshack.com/v2/1600x1200q90/924/IHDAWM.jpg


https://imagizer.imageshack.com/v2/1600x1200q90/921/YdMc8f.jpg


https://imagizer.imageshack.com/v2/1600x1200q90/921/EmXxsL.jpg



Thanks to Paul @ SupremePower for all his help with fitment and advice. [up] Fit perfectly.


Trying to decide if I want to put the factory center caps in or not. Pretty flush fit actually, not sure if the rear could use a 2mm spacer or just leave it.

Ordering Titanium bolts to drop some more weight and mass.

[HHughes1]

New offering from Neuspeed : 18x9.5 +45 20.2 lbs barrel designed specifically to clear TTRS / RS3 brakes including CC.

http://www.neuspeed.com/375/0/0/3945/8811218hs-rse11r-light-weight-wheel.html

[Paul@SupremePower]

Nuespeed RSe10s in Dark Bronze - 19x9 ET40 with Pilot Sport 4S's 265/35/19


https://imagizer.imageshack.com/v2/1600x1200q90/924/IHDAWM.jpg


https://imagizer.imageshack.com/v2/1600x1200q90/921/YdMc8f.jpg


https://imagizer.imageshack.com/v2/1600x1200q90/921/EmXxsL.jpg



Thanks to Paul @ SupremePower for all his help with fitment and advice. [up] Fit perfectly.


Trying to decide if I want to put the factory center caps in or not. Pretty flush fit actually, not sure if the rear could use a 2mm spacer or just leave it.

Ordering Titanium bolts to drop some more weight and mass.

Looks great Ben! 9 +40 is a good off the shelf spec for the 8S. For custom sets ups I’ve done, the front sits pretty much the same and i go
3-5mm lower in the rear. I think a 3mm more would be perfect and you’d be clear to lower it with no issues.

[Paul@SupremePower]

Our customer @getsideways_ the winner of the 2019 One Lap of America on his set of BC Forged:

BC Forged RZ23
19x10 +50 57.1 5x112

-over AP 9660 caliper
-spacer used to clear brakes and keep them square rotatable
-crystal burgundy
-machined for cone seat


https://i275.photobucket.com/albums/jj283/supremepowerparts/Allset/2BAD40AB-8E91-4C91-99C0-BA9D7B9FE4DF_zps297mmjt9.jpeg (http://s275.photobucket.com/user/supremepowerparts/media/Allset/2BAD40AB-8E91-4C91-99C0-BA9D7B9FE4DF_zps297mmjt9.jpeg.html)

https://i275.photobucket.com/albums/jj283/supremepowerparts/Allset/ADD7E284-0D77-40A5-BB30-9C2297D8ADCD_zpsmbmy3xzd.jpeg (http://s275.photobucket.com/user/supremepowerparts/media/Allset/ADD7E284-0D77-40A5-BB30-9C2297D8ADCD_zpsmbmy3xzd.jpeg.html)

https://i275.photobucket.com/albums/jj283/supremepowerparts/Allset/52BAB3D6-F9C0-4191-BA6D-2F046684F646_zpseig578sx.jpeg (http://s275.photobucket.com/user/supremepowerparts/media/Allset/52BAB3D6-F9C0-4191-BA6D-2F046684F646_zpseig578sx.jpeg.html)

https://i275.photobucket.com/albums/jj283/supremepowerparts/Allset/E177FA53-F204-4D82-ABCD-9CC4734BD2B4_zps8cskkhxo.jpeg (http://s275.photobucket.com/user/supremepowerparts/media/Allset/E177FA53-F204-4D82-ABCD-9CC4734BD2B4_zps8cskkhxo.jpeg.html)

[Chuckster]

That’s perfect!

[Rapture]

[QUOTE=Paul@SupremePower;13680716][B][SIZE=3]Our customer @getsideways_ the winner of the 2019 One Lap of America on his set of BC Forged:

BC Forged RZ23
19x10 +50 57.1 5x112

-over AP 9660 caliper
-spacer used to clear brakes and keep them square rotatable
-crystal burgundy
-machined for cone seat


https://i275.photobucket.com/albums/jj283/supremepowerparts/Allset/2BAD40AB-8E91-4C91-99C0-BA9D7B9FE4DF_zps297mmjt9.jpeg (http://s275.photobucket.com/user/supremepowerparts/media/Allset/2BAD40AB-8E91-4C91-99C0-BA9D7B9FE4DF_zps297mmjt9.jpeg.html)


Those do look nice. I like the concavity.

[Qwik23]

Neuspeed rse102 in gloss black.
19x9 45et
Michelin ps4s 255 35 19122419122420122421

Sent from my Pixel 3 XL using Tapatalk

[DtPuma]

I'm very much a wheel noob here, but I have a set of winter wheels and tires from my TTS. With my RS inbound, I wanted to see if they would fit. 7.5J x 18 ET51, with 225/40 R18 tires. I assume that bolt pattern and everything else are the same, but given that the front steel brakes are 2" larger than the TTS, I am concerned that they won't fit.

Thanks in advance for the help.

[Paul@SupremePower]

I'm very much a wheel noob here, but I have a set of winter wheels and tires from my TTS. With my RS inbound, I wanted to see if they would fit. 7.5J x 18 ET51, with 225/40 R18 tires. I assume that bolt pattern and everything else are the same, but given that the front steel brakes are 2" larger than the TTS, I am concerned that they won't fit.

Thanks in advance for the help.

Based on the above info I’d say no. Very few manufacturers have 18” that clear barrel and spoke for The TTRS. The other issue is the 7.5” width. That is probably more of problem because I haven’t seen any in that size work; in 18x7.5 or 19x7.5. You’d need to test fit to be sure but it doesn’t look probable.

[Cale262]

I'm running 20x9ET35 HRE FF01's with 275/30R20 PS4S and no issues what so ever. Suspension is MSS Sport full adjustable set very low with 034 4* camber plates.

https://photos.smugmug.com/-18-Audi-TT-RS/n-3Knz2D/i-zfbvqfB/0/728c7706/X3/i-zfbvqfB-X3.jpg

[DtPuma]

Great, thanks for the quick response. I appreciate your help.

[Audi TTRS]

Neuspeed rse102 in gloss black.
19x9 45et
Michelin ps4s 255 35 19122419122420122421

Sent from my Pixel 3 XL using TapatalkThis is the exact setup that I want. I also considered the rse10s. How does cornering feel? Grip, tire sidewall? Sorry for all of the questions

2018 TTRS stock

[Qwik23]

This is the exact setup that I want. I also considered the rse10s. How does cornering feel? Grip, tire sidewall? Sorry for all of the questions

2018 TTRS stockAll great so far. The only I may do is add some spacers for a bit more aggressive look. But otherwise pretty happy.

Sent from my Pixel 3 XL using Tapatalk

[EyeWin]

Our customer @getsideways_ the winner of the 2019 One Lap of America on his set of BC Forged:

BC Forged RZ23
19x10 +50 57.1 5x112

-over AP 9660 caliper
-spacer used to clear brakes and keep them square rotatable
-crystal burgundy
-machined for cone seat


https://i275.photobucket.com/albums/jj283/supremepowerparts/Allset/2BAD40AB-8E91-4C91-99C0-BA9D7B9FE4DF_zps297mmjt9.jpeg (http://s275.photobucket.com/user/supremepowerparts/media/Allset/2BAD40AB-8E91-4C91-99C0-BA9D7B9FE4DF_zps297mmjt9.jpeg.html)

https://i275.photobucket.com/albums/jj283/supremepowerparts/Allset/ADD7E284-0D77-40A5-BB30-9C2297D8ADCD_zpsmbmy3xzd.jpeg (http://s275.photobucket.com/user/supremepowerparts/media/Allset/ADD7E284-0D77-40A5-BB30-9C2297D8ADCD_zpsmbmy3xzd.jpeg.html)

https://i275.photobucket.com/albums/jj283/supremepowerparts/Allset/52BAB3D6-F9C0-4191-BA6D-2F046684F646_zpseig578sx.jpeg (http://s275.photobucket.com/user/supremepowerparts/media/Allset/52BAB3D6-F9C0-4191-BA6D-2F046684F646_zpseig578sx.jpeg.html)

https://i275.photobucket.com/albums/jj283/supremepowerparts/Allset/E177FA53-F204-4D82-ABCD-9CC4734BD2B4_zps8cskkhxo.jpeg (http://s275.photobucket.com/user/supremepowerparts/media/Allset/E177FA53-F204-4D82-ABCD-9CC4734BD2B4_zps8cskkhxo.jpeg.html)

Do you know if these will fit over the stock CCB on the TTRS? This exactly the set up what I’m wanting...

Thanks!

[Paul@SupremePower]

Do you know if these will fit over the stock CCB on the TTRS? This exactly the set up what I’m wanting...

Thanks!

To clear the brakes bolt on in 10 you’d need probably 19x10 +44 front and 19x10 +50 rear and to add some negative camber front and rear to avoid rub.

19x9.5 is a little easier to work with and can yield a nice fit with good concavity at stock camber. Shoot me an email if you’d like to discuss 👍

[blcksmth]

Is the suspension stock on this?

[blcksmth]

All great so far. The only I may do is add some spacers for a bit more aggressive look. But otherwise pretty happy.

Sent from my Pixel 3 XL using Tapatalk

So this is with stock suspension height?

[Qwik23]

So this is with stock suspension height?Yes

Sent from my Pixel 3 XL using Tapatalk

[Jeff_Jeske]

For those looking for a fairly light weight track friendly wheel and tire setup... the RSE10 19x9 +45 with 255/35/19 Bridgestone RE71R tire is a fantastic combination.
http://i64.tinypic.com/16lcyls.jpg

[JGreen76]

Just installed HRE FF04 20x9 et35 with MSS Sport Kit. No rubbing. Lowest setting in front, 5mm from lowest in rear.
131797131798131800


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[Paul@SupremePower]

Just installed HRE FF04 20x9 et35 with MSS Sport Kit. No rubbing. Lowest setting in front, 5mm from lowest in rear.
131797131798131800


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

I love bronze on white. And nice to see the 04s in a different finish. Well done.

[mtwallace85]

Just installed HRE FF04 20x9 et35 with MSS Sport Kit. No rubbing. Lowest setting in front, 5mm from lowest in rear.
131797131798131800


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

What tires and size are you running?

[tt-ho]

Just installed HRE FF04 20x9 et35 with MSS Sport Kit. No rubbing. Lowest setting in front, 5mm from lowest in rear.

Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

Good choice man!!! Looks great

[Chuckster]

They look like the stock sized tires.

[JGreen76]

Stock P-Zero. Thanks guys


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[TZilla]

Foremost, thanks Paul and Kim!

Neuspeed RSe11R 18x9 ET45 with 265/35R18 Yokohama A052

As an aside, I temporarily put my RSe10 18x8.5/8 ET45 stagger set from my RS 3 on the TT RS. On those, I could have the stick on wheel weights (avg thickness) at the very outside lip (raised area) and there were a few mm to the caliper on both the RS 3 and the TT RS. With the RSe11R, the weights very lightly interfere so it seems the barrel is a bit different.

https://i.ibb.co/DWG2MRW/New-Slate-Side.jpg
https://i.ibb.co/XVNPrw7/New-Slate2.jpg

[Paul@SupremePower]

Foremost, thanks Paul and Kim!

Neuspeed RSe11R 18x9 ET45 with 265/35R18 Yokohama A052

As an aside, I temporarily put my RSe10 18x8.5/8 ET45 stagger set from my RS 3 on the TT RS. On those, I could have the stick on wheel weights (avg thickness) at the very outside lip (raised area) and there were a few mm to the caliper on both the RS 3 and the TT RS. With the RSe11R, the weights very lightly interfere so it seems the barrel is a bit different.

https://i.ibb.co/DWG2MRW/New-Slate-Side.jpg
https://i.ibb.co/XVNPrw7/New-Slate2.jpg

Right on! Love it 👍👍

[tt-ho]

Thanks to Paul and Kim of Supreme Power for the help with the wheels!! Took awhile to decide but thanks to JGreen76 also for making decision easier 😁😁

HRE FF04 20x9 et35

134235134236

[Paul@SupremePower]

Thanks to Paul and Kim of Supreme Power for the help with the wheels!! Took awhile to decide but thanks to JGreen76 also for making decision easier 😁😁

HRE FF04 20x9 et35

134235134236

Well DAMN!

This is money. Right here:

https://i275.photobucket.com/albums/jj283/supremepowerparts/Allset/D5C110FD-D4F5-40F5-8194-FCD34BC66662_zps5wgzd7ln.png (http://s275.photobucket.com/user/supremepowerparts/media/Allset/D5C110FD-D4F5-40F5-8194-FCD34BC66662_zps5wgzd7ln.png.html)

[JGreen76]

Well DAMN!

This is money. Right here:

https://i275.photobucket.com/albums/jj283/supremepowerparts/Allset/D5C110FD-D4F5-40F5-8194-FCD34BC66662_zps5wgzd7ln.png (http://s275.photobucket.com/user/supremepowerparts/media/Allset/D5C110FD-D4F5-40F5-8194-FCD34BC66662_zps5wgzd7ln.png.html)

Straight FIRE

[HHughes1]

Rears are pretty even with the fender at 18x9.5 +53 with 275/35R18 RE71R tires. Even +45 would poke I’m guessing

107157

107158

107159


Stance will change when this finally gets here...

107166

I ordered a set of these today, really liked the 9 spoke design more than the 11 spoke Neuspeeds. Also got a great price from Vivid Racing !

[Dr Bill]

If anyone with DIRECT TPMS needs a set of sensors for extra wheels, I have a set here:

https://www.audizine.com/forum/showthread.php/860987-Genuine-Audi-TPMS-sensors-for-cars-with-dynamic-TPMS

This option is offered in Audi Sport models. If you don't have an MMI display with tire temp and pressure, you don't need these.
Thanks!

[McTTRS]

Spoke to APR yesterday and their S01 forged wheels will fit over the TT RS brake in the 18", 19" and 20" sizes - see here (https://www.goapr.com/products/wheels_s01_forged.html)

[HHughes1]

For track wheels they’re great. They do have small enough clearance to the caliper that rocks get stuck and scratch the barrel of the wheel. Sounds terrible and will go through the paint (my front wheels have a ring of silver where the rest of the barrel is black). Neuspeeds have a little more clearance it seems.

Mine arrived and I did a test fit without tires. I currently have negative 2.5 front and 2.25 rear which is making the strut clearance tight. The fronts clear the caliper by just over a hair however the barrel tapers wider away from the wheel face so I ordered some 5mm spacers to set the caliper a little further inside and also get just a little more clearance from the strut. I'm mounting 275 Hoosiers and I still have plenty of fender clearance even with the lowered ride height.

Point of clarification: The clearance challenge is with the barrel not the spokes

[mtwallace85]

https://uploads.tapatalk-cdn.com/20190815/e2e3164bf2052eda6aa3367fc85b91d7.jpg

[OHDAWG]

Which 18" will fit over the ceramic brakes?

[mtwallace85]

https://uploads.tapatalk-cdn.com/20190830/236e2762ea525520f3111c25e94cddda.jpg

19x9.5 et45 soon to be wrapped in Michelin PSS 265/35

[Nick_rs]

FYI TSW Interlagos 18 x 9.5 et 53 fit over the Ceramic Brakes139026139025

[OHDAWG]

https://i.ebayimg.com/00/s/ODAwWDgwMA==/z/UdwAAOSwOSVdYY1C/$_59.JPG

found these locally , they are et38. would these fit? 18x8.5"

he wants $1800 so im very tempted. talk me out of it.

- - - Updated - - -

[HHughes1]

FYI TSW Interlagos 18 x 9.5 et 53 fit over the Ceramic Brakes139026139025

I have slightly less clearance than that with the standard brakes. Wheel weights had to be placed in the center of the barrel

[Paul@SupremePower]

https://uploads.tapatalk-cdn.com/20190830/236e2762ea525520f3111c25e94cddda.jpg

19x9.5 et45 soon to be wrapped in Michelin PSS 265/35

Pics pics pics!!!

[mtwallace85]

Pics pics pics!!!

https://uploads.tapatalk-cdn.com/20191025/16773aee34250346bcd5e647e7025cab.plist
https://uploads.tapatalk-cdn.com/20191025/5bf1c8f5fae0a4e20e0d637f6edb32aa.plist
https://uploads.tapatalk-cdn.com/20191025/2c4dc2189c0c1891b80dd46386acdd2b.plist

I really need to invest in a DSLR, tired of taking iPhone pics lol.

[Paul@SupremePower]

https://uploads.tapatalk-cdn.com/20191025/16773aee34250346bcd5e647e7025cab.plist
https://uploads.tapatalk-cdn.com/20191025/1628d7845c554c393393058458407333.plist
https://uploads.tapatalk-cdn.com/20191025/44260bfe59fc47c9b71c6f1d3067ff6e.plist

I really need to invest in a DSLR, tired of taking iPhone pics lol.

Oh hell yes.

265/35 PSS?

What suspension?

And I say the same thing about my iPhone but they usually come out decent. I feel once I get a real camera there’s probably no going back tho.

[mtwallace85]

Oh hell yes.

265/35 PSS?

What suspension?

And I say the same thing about my iPhone but they usually come out decent. I feel once I get a real camera there’s probably no going back tho.

Correct on the tires and the suspension is stock magride. I’ll be getting the MSS lowering kit at some point and may throw the 5mm spacers I have in the back. Oh for sure. The iPhone pics are good for what the camera is, but it’s no comparison to a DSLR with a prime lens. It’s nearly impossible to keep the noise out of iPhone pics with the editing.

Fixed the pics. 2 of them were the wrong edits.

[mtwallace85]

https://uploads.tapatalk-cdn.com/20191101/23757fd6d5a2eeb275702e0444062a88.plist
https://uploads.tapatalk-cdn.com/20191101/7190adf2a19da5ae9f5abd0c176e1aea.plist

The iPhone 11 Pro Max camera is a little better.

[Paul@SupremePower]

💥New Vossen HF-5 for TTRS 8S💥

Hybrid forged/flow formed

Clears steel brakes in :

20x9 +35

Standard finishes:

-Gloss Black
-Matte Gunmetal

Available for shipping this month.

[email protected]



https://i275.photobucket.com/albums/jj283/supremepowerparts/Mobile%20Uploads/A9D05182-21FC-43FC-8D06-16982DFD0A92_zpsqioanlhu.jpeg (http://s275.photobucket.com/user/supremepowerparts/media/Mobile%20Uploads/A9D05182-21FC-43FC-8D06-16982DFD0A92_zpsqioanlhu.jpeg.html)

https://i275.photobucket.com/albums/jj283/supremepowerparts/Mobile%20Uploads/99A0F971-50D8-4A08-8F11-3BA04C1F8189_zpsqf0a8foq.jpeg (http://s275.photobucket.com/user/supremepowerparts/media/Mobile%20Uploads/99A0F971-50D8-4A08-8F11-3BA04C1F8189_zpsqf0a8foq.jpeg.html)

[apertura]

Winter Wheels are on my TTRS.

18x8 Rial Kodiak et31 and 235/45R18 Goodyear Ultra Grip WRT (not pictured)

Super cheap, made in Germany, and clear steel brakes with no spacers! Have put 200 miles on them already and they ride great.

https://i.imgur.com/UH2iAmG.jpg

https://i.imgur.com/WEPG04h.jpg

Hello, how much clearence do you have between calipper and spokes?

Thanks in advance for your help

[Jeff_Jeske]

For awhile I was kicking myself for buying 20" wheels again but I still love the look of my Schmidt Revolution 20x9 +39 wheels. I've got a bunch of different center caps to change up the look from time to time as well.
https://i.ibb.co/CKm8GKF/PEXT6129.jpg (https://ibb.co/XxjLRxT)

For track duty I have a couple sets of RSE10 in 19x9.
https://i.ibb.co/DLqhdxr/HXCS5596.jpg (https://ibb.co/GFhymKH)

For whatever reason I like that "Y" design.
https://i.ibb.co/Zdk2xvv/SJFC2057.jpg (https://ibb.co/hstYVrr)

One more for good measure.
https://i.ibb.co/DtcSsWj/IMG-1290.jpg (https://ibb.co/G0YbBpr)

[apertura]

Winter Wheels are on my TTRS.

18x8 Rial Kodiak et31 and 235/45R18 Goodyear Ultra Grip WRT (not pictured)

Super cheap, made in Germany, and clear steel brakes with no spacers! Have put 200 miles on them already and they ride great.

https://i.imgur.com/UH2iAmG.jpg

https://i.imgur.com/WEPG04h.jpg


Hello, can I ask how much clearence between the spokes and the caliper?

[RyanS3]

For awhile I was kicking myself for buying 20" wheels again but I still love the look of my Schmidt Revolution 20x9 +39 wheels. I've got a bunch of different center caps to change up the look from time to time as well.
https://i.ibb.co/CKm8GKF/PEXT6129.jpg (https://ibb.co/XxjLRxT)

For track duty I have a couple sets of RSE10 in 19x9.
https://i.ibb.co/DLqhdxr/HXCS5596.jpg (https://ibb.co/GFhymKH)

For whatever reason I like that "Y" design.
https://i.ibb.co/Zdk2xvv/SJFC2057.jpg (https://ibb.co/hstYVrr)

One more for good measure.
https://i.ibb.co/DtcSsWj/IMG-1290.jpg (https://ibb.co/G0YbBpr)

RSE10 in 19x9, what tire spec?
Thx!

[RyanS3]

Neuspeed rse102 in gloss black.
19x9 45et
Michelin ps4s 255 35 19122419122420122421

Sent from my Pixel 3 XL using Tapatalk


Good work!

Neuspeed rse102 in gloss black.
19x9 45et
Michelin ps4s 255 35 19

No spacers, no issues?
I’m considering this spec combo with all seasons for PA winters
Cheers

[Qwik23]

Good work!

Neuspeed rse102 in gloss black.
19x9 45et
Michelin ps4s 255 35 19

No spacers, no issues?
I’m considering this spec combo with all seasons for PA winters
CheersNo spacers yet. May do a small one on the rears. But no issues at all with fit.

Sent from my SM-G975W using Tapatalk

[ReallyNotHalvie]

Pics pics pics!!!

What is the recommended fitment on these? Different than the RS3 or still 9.5 +45?

[Paul@SupremePower]

What is the recommended fitment on these? Different than the RS3 or still 9.5 +45?

9.5 +45 front +40 rear is solid imo.

[mtwallace85]

9.5 +45 front +40 rear is solid imo.

Interesting. I may have to throw my 5mm spacers on in the back, then.

[Paul@SupremePower]

Interesting. I may have to throw my 5mm spacers on in the back, then.

This is 19x9.5 +45 front 9.5 +42 rear with 265/35 PS4S

+40 with that tire is money in the rear.

http://i275.photobucket.com/albums/jj283/supremepowerparts/Allset/4C3AA2C0-705A-4376-BEB8-49FBCB5C29CC_zpsubavwjjv.jpg (http://s275.photobucket.com/user/supremepowerparts/media/Allset/4C3AA2C0-705A-4376-BEB8-49FBCB5C29CC_zpsubavwjjv.jpg.html)

[GaBoYnFla]

Anyone running a staggered setup? I've always been against this because it's all look and not go. Found a wheel I like offered as staggered. 8.5 front and 10" rear. I'm guessing that since the tire patch is the same, the effects for street use would be minimal? Anyone with experience with this? And these wheels? I would want the center spokes to be blue and the lip to be gloss black.

https://i22.photobucket.com/albums/b304/GaBoYnFla/Posting%20Pics/Lexani%20Forged%20LZ-102_305_a2.png




And this one is forged but not enough blue on it....

https://i22.photobucket.com/albums/b304/GaBoYnFla/Posting%20Pics/Lexani%20R12%20Satin%20Black-Blue-Lip---Angle-a2.png




Oh yea, here is the car:

https://i22.photobucket.com/albums/b304/GaBoYnFla/2019%20Audi%20TTRS/AF96D591-D1B8-42E3-94D5-79A718E1FCCE.jpeg

[ReallyNotHalvie]

Another data point.

Neuspeed RSE122 wheels fit fine. 18 x 9.5 ET45 with 265/35R18 RE71R tires.


Nuespeed RSe10s in Dark Bronze - 19x9 ET40 with Pilot Sport 4S's 265/35/19


https://imagizer.imageshack.com/v2/1600x1200q90/924/IHDAWM.jpg



Has anyone tried 18x9.5 265/40r18? If 265/35r19 works, shouldn't it?

[Paul@SupremePower]

Has anyone tried 18x9.5 265/40r18? If 265/35r19 works, shouldn't it?

I know 265/40-18 is a go on 18x9 +45.

Should be ok too on 18x9.5 +45 just pay attention to the front if very low and/or with a wide running tire.

I’d do 275/35-18 on 9.5 +45 tho. Would handle better imo.

[Zedstts]

This is 19x9.5 +45 front 9.5 +42 rear with 265/35 PS4S

+40 with that tire is money in the rear.

http://i275.photobucket.com/albums/jj283/supremepowerparts/Allset/4C3AA2C0-705A-4376-BEB8-49FBCB5C29CC_zpsubavwjjv.jpg (http://s275.photobucket.com/user/supremepowerparts/media/Allset/4C3AA2C0-705A-4376-BEB8-49FBCB5C29CC_zpsubavwjjv.jpg.html)Is this stock ride height?

Sent from my SM-G955U using Audizine mobile app (http://r.tapatalk.com/byo?rid=87676)

[Paul@SupremePower]

Is this stock ride height?

Sent from my SM-G955U using Audizine mobile app (http://r.tapatalk.com/byo?rid=87676)

Lowered on KW HAS

[Zedstts]

Would a 19x9.5 ET 45 with 255s fit stock ride height [emoji848]
Lowered on KW HAS

Sent from my SM-G955U using Audizine mobile app (http://r.tapatalk.com/byo?rid=87676)

[Paul@SupremePower]

Would a 19x9.5 ET 45 with 255s fit stock ride height [emoji848]

Sent from my SM-G955U using Audizine mobile app (http://r.tapatalk.com/byo?rid=87676)

All day long. You can do 265 just as easy. It’s fine even lowered on 9.5 +45

[BeTTo RS]

https://i.ebayimg.com/00/s/ODAwWDgwMA==/z/UdwAAOSwOSVdYY1C/$_59.JPG

found these locally , they are et38. would these fit? 18x8.5"

he wants $1800 so im very tempted. talk me out of it.

- - - Updated - - -


They are pretty cheap! Those BBS RS-GT hace or had a retail price of $1,200.00 USD per wheel. Since they’re ET 38 I guess they’ll fit very well... even the size of the front BBK.

[Zedstts]

Fitment on point! Hit a nail driving to work because im a nurse and we are ready for covid!
Side not my rohanas will be in this week 167367

Sent from my SM-G955U using Audizine mobile app (http://r.tapatalk.com/byo?rid=87676)

[BeTTo RS]

Fitment on point! Hit a nail driving to work because im a nurse and we are ready for covid!
Side not my rohanas will be in this week 167367

Sent from my SM-G955U using Audizine mobile app (http://r.tapatalk.com/byo?rid=87676)

Keep the good work!

[VAGking]

https://uploads.tapatalk-cdn.com/20200320/1b65cc487203301ae882c83082190e85.jpg


Motec ultralights 20x9 ET 45 just under 20 lbs


Sent from my iPhone using Tapatalk

[Rapture]

Anyone running a staggered setup? I've always been against this because it's all look and not go. Found a wheel I like offered as staggered. 8.5 front and 10" rear. I'm guessing that since the tire patch is the same, the effects for street use would be minimal? Anyone with experience with this? And these wheels? I would want the center spokes to be blue and the lip to be gloss black.

https://i22.photobucket.com/albums/b304/GaBoYnFla/Posting%20Pics/Lexani%20Forged%20LZ-102_305_a2.png




And this one is forged but not enough blue on it....

https://i22.photobucket.com/albums/b304/GaBoYnFla/Posting%20Pics/Lexani%20R12%20Satin%20Black-Blue-Lip---Angle-a2.png




Oh yea, here is the car:

https://i22.photobucket.com/albums/b304/GaBoYnFla/2019%20Audi%20TTRS/AF96D591-D1B8-42E3-94D5-79A718E1FCCE.jpeg

I Run a staggered "offset" 20x9.5 HRE P101. The rear is at ET40 with aggressive concavity, the front is ET46, no concavity. 265/30/20 P4S all around so same contact patch, etc. I love the fitment.

[Lofvis]

Q: I'm running/lowered on kw coilovers v3.
Getting some oem 20 inch wheels, should I go with the standard 255/30/20 or 265/30/20?
Will be running the ps 4s tire.
The car might see 1 or 2 track days a year, doing mostly "aggressive dd"

[FLAWLES5]

Stock rims are best looking, buy heavy pigs. IMHO

Sent from my SM-G955F using Audizine mobile app (http://r.tapatalk.com/byo?rid=87676)

[GaBoYnFla]

Stock rims are best looking, buy heavy pigs. IMHO

Sent from my SM-G955F using Audizine mobile app (http://r.tapatalk.com/byo?rid=87676)

They are forged so lighter than you think. Anyone know what they weigh? The 20"s.

[mtwallace85]

They are forged so lighter than you think. Anyone know what they weigh? The 20"s.

There’s a thread on this somewhere but I’m too lazy to find it. I believe mine weighed 26.5lbs. My 19” BC Forged wheels only saved a couple pounds per corner. Never mind, it was easy to find lol.

https://www.audizine.com/forum/showthread.php/884883-Stock-20-quot-Rim-Weight

[FLAWLES5]

They are forged so lighter than you think. Anyone know what they weigh? The 20"s.I know what I'm talking about. R20 Rim weight around 27lbs.

Sent from my SM-G955F using Audizine mobile app (http://r.tapatalk.com/byo?rid=87676)

[FLAWLES5]

Oem pirelli p zero 255 30 20" = 23 lbs
Combo rim & tire + tpms + balance weights + air ~ 23.8kg [emoji33] ~ 50.7 lbs per corner!
Heavy or Not? I think asfck.169063169064

Sent from my SM-G955F using Audizine mobile app (http://r.tapatalk.com/byo?rid=87676)

[Lofvis]

From the lack of response I'm guessing no one is running a 265 tire on a 20x9 wheel on a lowered car.

[Paul@SupremePower]

From the lack of response I'm guessing no one is running a 265 tire on a 20x9 wheel on a lowered car.

265/30-20 on the Oem 20x9 +52 is doable lowered. I wouldn’t go wider than 265 on 9” though

[DocSean]

I'm running a 275/30 on the oem 9" wheel just fine, but I am not lowered. Upon inspection I don't see there being any issues if I decided to lower the car. 9" is the minimum recommended (by Michelin) for a 275 width.

[Lofvis]

Thx, will see what the tire shop respond.
Car wont see much track use but better to have that little extra side wall of the 265 vs 255.

[Solution]

I really like the HRE FF01 19x9.5 et45. Equipped w/265/35/19, will there be any fitment issues? I'm on MSS springs but eventually plan to go KW. Not slammed by any means. Been difficult to find answers on this elsewhere. Most people seem to be running 255's, but they look a little weak on a 9.5" wheel.

[HHughes1]

I have BC Forged in 19x9.5 +45 with 265/35 Cup 2’S. MSS springs near lowest setting 183787


Sent from my iPhone using Audizine (http://r.tapatalk.com/byo?rid=87676)

[Paul@SupremePower]

I really like the HRE FF01 19x9.5 et45. Equipped w/265/35/19, will there be any fitment issues? I'm on MSS springs but eventually plan to go KW. Not slammed by any means. Been difficult to find answers on this elsewhere. Most people seem to be running 255's, but they look a little weak on a 9.5" wheel.

19x9.5 +45 with 265/35-19 square is solid lowered an inch. But I’ve done more 9.5 +45 front with 9.5 +42 rear with 265/35 for customers as it flushes out the rear better. This is that on KW HAS:


https://hosting.photobucket.com/albums/jj283/supremepowerparts/Allset/.highres/4C3AA2C0-705A-4376-BEB8-49FBCB5C29CC_zpsubavwjjv.jpg (https://app.photobucket.com/u/supremepowerparts/a/3bfd0c22-7b2d-459c-bb1e-01032122c82c/p/af4f116d-7662-44cb-b703-490f54d15ce4)

[mtwallace85]

I really like the HRE FF01 19x9.5 et45. Equipped w/265/35/19, will there be any fitment issues? I'm on MSS springs but eventually plan to go KW. Not slammed by any means. Been difficult to find answers on this elsewhere. Most people seem to be running 255's, but they look a little weak on a 9.5" wheel.

You won’t have any figment issues at all. I run the same specs and haven’t rubbed once. There’s also definitely room to lower my car without introducing any rubbing.

https://uploads.tapatalk-cdn.com/20200619/8289a89b61d3b75ef99b1bc665cbbe33.plist

https://uploads.tapatalk-cdn.com/20200619/5997188824458fe87ed869123c81115b.plist

[Paul@SupremePower]

You won’t have any figment issues at all. I run the same specs and haven’t rubbed once. There’s also definitely room to lower my car without introducing any rubbing.

https://uploads.tapatalk-cdn.com/20200619/8289a89b61d3b75ef99b1bc665cbbe33.plist

https://uploads.tapatalk-cdn.com/20200619/5997188824458fe87ed869123c81115b.plist

We’re gonna be wheel twins. I just ordered a set of HCA162 for my RS3. Same finishes except hidden hardware. So bad ass.